Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Product Features
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.
In this video, we're going to be working with our 2011 Chevy Camaro. We're going to show you how to remove and replace your rear brake pads and rotors. We're showing you this on the passenger side but the procedure is the same on the driver side and we recommend you replace your brakes in pairs. If you like this video, please click subscribe. We have a ton more information on this and many other vehicles and if you need these parts for your car you can follow the link down in the description over to 1AAuto.com. Here are the items you'll need for this procedure.
Loosen all of your lug nuts with a 22 millimeter socket and a breaker bar or a long ratchet. Raise and support your vehicle. We're using a lift to make it easier to show you what's going on but this job can easily be performed at home with a jack and jack stands. Finish removing all of your lug nuts. You should be able to do this by hand now, but you can use a 22 millimeter socket and ratchet if necessary. Remove your wheel and tire.
Using a T30 Torx socket, a ratchet, and an extension, remove the rotor screw. If yours is stuck, you can use a box end wrench on the lugs like this to counter hold it while you loosen the screw.
Loosen and remove the two 14 millimeter caliper guide pin bolts. Do this with a 14 millimeter socket and ratchet. If yours is spinning, you can either get a skinny wrench on the hex of the caliper bolt here, or you can go ahead and grab that with a pair of pliers. These bolts are one time use only, so be sure if you're removing them, you have a new set to replace them with. Remove your caliper and hang it somewhere safe and out of the way with something like a bungee cord, zip ties, or mechanic's wire. Really all you want to do is make sure that you're not putting any stress on the rubber hose.
Remove your brake pads. If yours are stuck in there, you can use a flat blade screwdriver or a small pry bar to pop them out. Otherwise, just take them out by hand. Loosen the two 16 millimeter caliper bracket bolts with a 16 millimeter socket and a breaker bar. These bolts are also one time use, so again, if you're going to be loosening them or removing them, be sure you have a new set handy. Once we've cracked them loose, we'll switch over to a 16 millimeter socket and ratchet. Then remove your caliper bracket from the vehicle.
Now, your rotor may be stuck on. First, always be sure your e-brake is off so you don't damage that when removing the rotor. If you're not saving the rotor, you can go ahead and hit the faces of the rotor to knock it loose. Or if you want to save the rotor because you're getting it turned or just replacing another component, you can hit the hub of the rotor between the studs and that'll usually free it up enough to get it off.
Use a flat blade screwdriver to pop off your brake shims. Now, ours aren't in bad shape so you can just use a wire brush and remove all the dirt and debris from them. As long as they don't have any heavy rust build up or they aren't broken or have lost that spring, you can go ahead and just clean them like this. Or if yours are really bad, you can always just replace them with a nice new set.
Either way, you'll want to use a steel wire brush to bring down all the corrosion and buildup where the actual shims sit in the caliper bracket. You don't have to go crazy here and make these a brand new polished clean surface. You just want to make sure you get the heavy stuff off so your new shims sit on there nice and straight.
We'll put a thin coat of brake grease where we just cleaned. This will keep our shims from corroding and getting stuck onto the bracket, as well as helping to prevent any other rust and debris buildup for the next time we need to do our brakes. We'll just be able to wipe the old grease off and then wipe some new stuff on and save us some time later. Hold the boot and slide your caliper pin out. Wipe off all the old grease with a paper towel. Now, this is nice and clean and smooth so we'll just re-grease this and throw it back in. If you have any heavy rust buildup or corrosion, you'll need to either sand them down and grind them if it's not bad, or if they have some really heavy buildup, they can be replaced. Ours looks good, so we'll just throw some new grease on there and pop it back into the boot. Make sure that it actually seals back into that boot, and then we'll do the same thing with the other pin.
Install your shims. Pop into place. Then we'll apply some grease to the top of these too, again, to prevent them from corroding and also to make sure that our pads move smoothly and quietly along the guide.
Make sure you clean up any rust buildup on your hub as well. The face of our hub is actually still nice and clean, but the bore has got some buildup on there, so we're just going to take our wire brush and knock it down. Again, don't need to have a perfectly clean hub when we're done here, but getting this debris off will make our new rotor go on nice and easy and help prevent it from getting stuck on there again in the future. Then put a thin coat of grease on here. Same idea, this is just going to prevent rust buildup later on, make sure our rotors come off nice and easy in the future, and save us the headache of needing to clean all this surface down next time.
Install your rotor onto the hub backwards and spray down the inner piece here because this is what's called a drum and hat rotor, which means our e-brake is actually a miniature brake drum that sits inside of here, so this is its contact surface, and then we'll want to spray the back face of the rotor as well to remove the solvent they use to keep these from rusting when they're in the warehouse. Flip the rotor over and install it the right way. Be sure to line up your rotor's screw hole with the threads in the hub. We'll spray this side down as well.
Reinstall your rotor screw. Now these don't actually have any kind of structural integrity or function to them other than holding the rotor upright when you install your new rotor, so I'm just using my T30 Torx socket on the end of an extension just to help keep that upright and make installing our caliper bracket, pads, and calipers a little bit easier.
Reinstall your caliper bracket and start your two new 16 millimeter caliper bracket bolts by hand. We'll then bring them down close with our 16 millimeter socket and ratchet. We'll then torque the bolts to 30 foot-pounds. We'll then add 90 degrees to the bolts. Now, you could use a torque angle gauge for this, but 90 degrees is pretty easy to eyeball. Trust me when I say once these bolts are down tight, they're down tight. You won't get them any further than that 90 degrees.
Install your new brake pads. Grease the back side of both your brake pads. This will help prevent them from sticking to our calipers as well as making sure they're nice and quiet and smooth.
Unhook your caliper from whatever you used to secure it out of the way. We'll then use a pair of tongue and groove or slide jaw pliers to slowly compress the piston on the caliper.
Reinstall your caliper. Install your new caliper bolts. We'll do the same thing, we'll hold the guide from spinning with a pair of pliers and torque these to 20 foot-pounds. The manual does say these bolts are one time use. However, we don't have to add a degree angle to them to torque to yield, but where the manual says to replace them, we went ahead and threw a new set in.
Reinstall your wheel and tire and get all five of your 22 millimeter lug nuts on as tight as you can by hand. Torque your lug nuts to 140 foot-pounds in a cross pattern.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Hi. I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
Hi guys. Sue here at 1A Auto. Today we're going to be installing these front brakes on this 2012 Equinox. These brakes are Nakamoto and you can buy them at 1A Auto online. They are superior balanced and reduce vibration and abnormal wear. They also have proper thermal efficiency and weight distribution.
We're going to start the front brake job on this 2012 Equinox. First thing I'm going to do is use a breaker bar, a 22 millimeter socket and snap free all of the lug nuts. We remove all the lug nuts and set them aside someplace where you won't lose them, preferably not in dirt either. On this 2012 Equinox it has ABS and on ABS brake systems when you're doing brake jobs, front or rear, you want to open the bleeder screw. Very important that you do not push the piston back and let the brake fluid go in reverse flow, you can damage the ABS module.
Here I've got a catch basin to catch any brake fluid that comes out and leaks. Now I'm going to take the caliper sliding bolts off. 14 millimeter head. You can break them free just enough to use your hands. Set them aside. Now we're going to pry the caliper off of the caliper bracket. I like to use a little small pry bar or a screwdriver flathead. Just work it back and forth. Make sure you aim that bleeder screw into that bucket. Now we're going to push that piston back. I use here a pair of just vise grip welding clips, very easy, you can get at any parts store.
Here's a good time when you can examine the fluid to see if it's discolored, black, if it has a smell to it. You want your fluid to stay nice and clear and a yellow. If it's ever black or brown, it's very important you might want to flush that brake system. Inadequate stopping and damage to everything that has a rubber seal to it will occur.
With that clamp in there you want to re-tighten that bleeder screw. Just a half turn, quarter turn is all I used, you don't need to take the screw all the way out. Just give it a quick snug. I'm going to hang the caliper because you never want to just let that dangle down, it can do damage to the actual brake line. Let that set aside, now it's out of your way. Now I'm going to break free the caliper bracket bolt that mounts to the knuckle. This particular size is an 18 millimeter socket. Then you're going to remove the bracket from the rotor. Nice quick tug.
Now we're going to remove the Torx head holding mounting screw to the hub. Torx head looks like a star, this particular star head is a 30. Make sure you set it aside because you're going to reuse it. Now when it comes to removing the rotor off the hub, you'll see rust rings from the weather. Welcome to New England. We'll use a penetrating spray, soak that down a little bit, it's going to help you remove this with a little less effort. When hitting the rotor, you want to make sure you do not hit the lug nuts obviously, you can strip them.
Here we have comparison of the new rotor and pads compared to the old rotor and pads. These pads are worn quite down. If I measure them with the tool we have 3 millimeter to 2/32, which is right there. That is definitely the indicator has been hitting, it's time for a new set of brakes. If you look at the rotor on the back surface you'll see this customer was probably having a bit of a pulsation. Rough surface causes the brake pedal to pulsate when you come to braking. New rotor to old rotor, the hats are the same, same weight, thickness and the same amount of fins for cooling.
Now we've got the bracket, I'm going to put it in the box here so we can catch our Brakleen when we clean it. I'm going to hammer out the brake pads, just like the rotors, stuck in there. Look at that New England dust. There you go, there's your bracket and if you've never done brakes before note which one was the outer pad and which one was the inner pad because you're going to want that when you assemble it together. The inner pad will have the circle from the caliper piston and the outer pad will have the little ear notches from the fingers on the caliper. Easy. Also the indicator usually goes on the inside.
Now I'm going to remove the tin. Little pry bar to remove. This particular model there is no up or down, top or bottom, difference between the brake tins. Take a wire brush. You want to clean the rust off of the surface. Pick yourself up a can of brake parts cleaner, just give it a little squirt. You do this to help the brakes work their best, last longer. I'm going to give the tins just a little scuff, you don't want any rust in there. This is the surface that the pad actually slides on back and forth as the caliper moves as your foot goes on the brake pedal and decompresses the caliper piston. Smoother surface, smoother action. We'll leave those to dry.
While that's drying I'm going to show you how to apply brake caliper grease. You just want a thin coat. This will stop any rust from forming under the tins. When rust forms under the tins it'll push the pads closer together so they won't slide back and forth. Without sliding you have a sticky pad, pad sticks, wears down to the metal. I'm going to just lock the tin back in there. You don't want to put grease or silicone paste on the top where the pad slides, for that will collect this lovely road dust and brake dust and cause it to jam in it's way. Easy peasy.
Now we're going to clean and lubricate the caliper slider pins. Quick reference, there's a top and bottom pin on most vehicles. You'll find a rubber boot on the tip. If you don't do one at a time and you happen to drop it or mix them up, usually the rubber boot goes on the top part of the caliper. With that out I'm going to clean off all the old grease with a rag. I'm going to look in the boot and examine it. You don't want any tears or holes. If water gets in there, that'll seize this pin up from sliding and cause improper pad wear.
With the same caliper grease, I like a light coating. This also will help with the chatter. Sometimes people hear creaking when they apply their brake pedal, that means that the sliding grease has worn out. I also like to lube the inside of the boot, a little bit of a dab at the end, not too much. Now we're going to do the same thing to the other side. This is the caliper mounting bolt and from the factory they come with Loctite. These bolts will be torqued to 140 foot pounds, so the manufacturer in this case strongly recommends reapplying Loctite. I like to clean off the old Loctite, the best you can. I use a wire brush. And then I'm going to be applying some Loctite. Just let it work all the way around the threads.
With the brakes off and now we're going to clean up the hub surface that the new rotor is going to ride on. I have a wire brush here. Look at all that. You can use some Brakleen to soften that up. Now with the hub clean I'm going to just temporarily install the rotor so that I can spray it down with Brakleen. I want to get the protective grease that they put on, it's like a silicone or spray, to protect it from rusting on the shelf. Turn it around, we'll do the same. Now I'm going to take the rotor off that I've cleaned and set it aside.
With the hub cleaned from rust the best we can do, I like to add a little Never-Seez, that way in the future for the next person they don't have to go through what we went through. You don't have to put a lot, it stays there and it's heat tempered. Now with that all set you line the mounting bolt hole up with the hole in the hub. This is that Torx fitted screw again. I'm going to start with the hand. Just snug it down.
Now we're at the point we're going to install the front caliper bracket on this 2012 Equinox. I've already preloaded Loctite on my mounting bolt. Thread it by hand. Once you have them snug, now we're going to torque them to 140 foot pounds. Now it's time to install the new pads. Just like I said earlier when we tore it apart, the indicator clip usually goes on the inside of the rotor. Press it down in the clip, slide it in. See how smooth that went? No fighting, that's an indication of good rust cleaning. There we go, they're in. We're going to mount the caliper now.
Make sure you always start everything by hand, that way you don't cross thread. Once those are hand snug, the manufacturer recommends 20 foot pounds. Now that the brake job is assembled completely, because we had the bleeder screw open to push back that piston we're going to do just a gravity bleed, so make sure you have a bucket below that bleeder screw. You just want to turn that bleeder screw maybe a half a turn. Keep an eye on the fluid. That's a nice, clean drip. No need to touch the brake pedal, we're not doing a power bleed we're just doing a gravity bleed. You want to make sure there's no air pockets. It just gives it a nice brake pedal and make sure you don't have a sinking pedal. That looks great, we're going to tighten her up.
Always put the boot back on to stop from the road dirt and rust. Now we're going to clean all that brake fluid off with brake parts cleaner. Now we're going to mount the tire back on. I'm just going to hand snug the lug nuts because we're going to use the manufacturer's wheel torque once it gets on the ground, it's 140 foot pounds. When doing this at home, you want to lower the jack so that the tire is just starting to hit the ground, don't want all the weight of the vehicle while you tighten these lug nuts. As you can see I'm doing the star pattern, that distributes the pressure equally around that hub.
Okay. Now that we're done with the front brake service on this 2012 Equinox we're going to check the brake fluid level. You always want to use the brake fluid that the manufacturer recommends, in this case it's DOT 3. There's a line that you want to go to and not overfill, because brake fluid expands. As you can see, the line indicator on the side here, both sides. I'm just a smidge below it, I'll add a little more. Make sure your brake fluid cover is free of any dust or dirt.
Once your brake job is completed and you've topped off the brake fluid, it's always great idea to pump your brake pedal up before you start the vehicle or try to drive it.
Thanks for watching. Visit is at 1aauto.com for quality auto parts, fast and free shipping and the best customer service in the industry.
