Replaces

2010-13 Toyota Prius Strut & Spring Assembly Pair TRQ SCA57239 - 1ASSP01190

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   Pair

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wiper Arms (0:25)
    • Pry the cap off the driver side wiper arm stud
    • Remove the 14mm nut from the stud
    • Pull the wiper arm off the stud
    • Open the hood
    • Remove the two 14mm mounting nuts from the passenger side wiper arm
    • Pull the wiper arm off the windshield
  2. step : Removing the Cowl Cover (2:10)
    • Pry off the two cowl corner trim pieces with a trim tool
    • Pry the two push clips out of each side of the cowl with a flat blade screwdriver
    • Release the clips along the front of the cowl
    • Lift the cowl up and out of the engine bay
  3. step : Removing the Wiper Transmission (3:45)
    • Unplug the wiper motor electrical connector
    • Unclip the wiring harness from the lower wiper cowl
    • Remove the four 10mm bolts from the wiper transmission
    • Pull the wiper transmission off the lower wiper cowl
  4. step : Removing the Lower Cowl Panel (5:00)
    • Remove the nine 10mm bolts
    • Lift the lower cowl panel out of the engine compartment
  5. step : Removing the Wheel (6:13)
    • Pry off the wheel cover with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground with a 21mm socket and breaker bar
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  6. step : Removing the Strut (6:57)
    • Counterhold the upper sway bar nut with a 6mm hex drive
    • Loosen the 17mm nut from the sway bar with a 17mm wrench
    • Remove the upper sway bar link from the strut
    • Loosen the 12mm bolt and remove the ABS wire bracket from the strut
    • Loosen the strut nuts with a 22mm socket and a breaker bar
    • Remove the lower bolts
    • Remove the three nuts from the top of the strut with a 14mm socket
    • Remove the bolt from the bottom of the strut
    • Lower the strut down and out
  7. step : Installing the Strut (12:23)
    • Insert the strut up into place
    • Tighten the three nuts to the top of the strut with a 15mm deep socket and ratchet
    • Line up the bolt holes with the knuckle
    • Thread a nut on top by hand
    • Insert two lower strut bolts by hand
    • Tighten the lower bolts with a 22mm socket and ratchet and 17mm wrench
    • Torque the bolts to 177 foot-pounds
    • Insert the sway bar link to the strut
    • Tighten the upper bolt with a 17mm wrench and 6mm hex drive
    • Torqe the sway bar link upper nut to 55 foot-pounds
    • Clip in the ABS wire and tighten the 12mm bolt
  8. step : Reattaching the Wheel (16:22)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 76 foot-pounds in a crossing or star pattern
    • Press on the hub cap
  9. step : Installing the Lower Cowl Panel (17:31)
    • Insert the lower cowl panel into place
    • Tighten the nine 10mm bolts to the panel
  10. step : Installing the Wiper Transmission (18:41)
    • Line up the wiper transmission
    • Insert the wiper transmission pin into the rubber grommet
    • Insert the four 10mm bolts into the wiper transmission
    • Plug in the wiper motor electrical connector
    • Clip the wiring harness to the lower wiper cowl
  11. step : Installing the Cowl Cover (20:13)
    • Slide the cowl under the windshield
    • Push in the clips along the front of the cowl
    • Insert the two push clips into each side of the cowl
    • Clip the corner trim piece onto each side of the cowl
  12. step : Installing the Wiper Arms (21:20)
    • Line up the passenger side wiper arm on the windshield
    • Fasten the two 14mm nuts onto the wiper arm
    • Line up the driver side wiper arm on its stud
    • Fasten the 14mm nut onto the stud
    • Push the cap onto the wiper stud
    • Close the hood

Tools needed for replacement:

    Allen Wrenches

  • 6mm Allen Wrench

  • General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 14mm Socket
  • 17mm Socket
  • 21mm Socket
  • 10mm Socket
  • 22mm Socket

  • Specialty Tools

  • Trim Tool Set

  • Wrenches - Metric

  • 17mm Wrench
  • 10mm Wrench
  • 22mm Wrench

3.00/ 5.0
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
1
0
1
Bumpy
I installed these on my 2012 Prius two. They are incredibly bumpy and make a lot of noise. I suspect the noise is coming from the boots.
January 16, 2017
shocks great but make lots of noise
shock shaft seal squeaks and the top bushing grumbles, very hard to check before install then to late. took 5 hours to install and now must take out and try lube put back and then maybe take apart again and replace. and you can bet they will not be this brand.
July 30, 2017
Perfect fit!
I ordered the basic replacements struts for my 2010 Prius. Also ordered the recommended sway bar links. The parts were a perfect fit and the "how to" video was flawless.
July 18, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2010-2013Toyota Prius Toyota Prius Front Strut & Spring Assembly Pair TRQ SCA57239
Part #: 1ASSP01190


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: SCA57239

How-to Video:

(22:25 min)