Replaces

2010-13 Toyota Prius Complete Strut Assembly & Shock Absorber Kit TRQ SK62116 - 1ASSP01655

Part Details

  • Quantity: 4 Piece Set

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing Trim Panels to Gain More Access (0:23)
    • Unlock and remove the trunk floor
    • Remove the plastic tray
    • Remove the side cover
    • Remove the trim piece from the edge of the trunk area
    • Use 10m socket to remove the two cargo tie-down hooks
    • Fold the rear seat
    • Remove main side panel by prying and popping it out in the trunk door area
    • Remove the plastic cover for the privacy cover
    • Continue popping out the main side panel from the back seat area
  2. step : Removing the Wheel (3:30)
    • Remove the hubcap
    • Use a 21mm socket and a breaker bar to loosen the lug nuts
    • Raise and support the car
    • Continue removing the lug nuts
    • Remove the wheel from the car
  3. step : Removing the Shock Absorber (4:29)
    • Use a jack to put a little pressure on the side you are working on
    • Spray rust penetrant to help remove the hardware
    • Use 17mm socket and a breaker bar to loosen the lower nut
    • Use a 17mm socket on a ratchet to remove the nut and bolt the rest of the way
    • While holding the shock absorber with one arm, take the upper nut off
    • Pull the sock assembly out
  4. step : Reinstalling the New Shock Absorber (7:24)
    • Cut the shipping strap off
    • Put the old bump stop / dust cap on the new shock
    • Slide the sock up in place and insert the bottom bolt and nut
    • Install the new locking nut at the top
    • Use 5mm hex key to hold the top of the shock
    • Use 18mm wrench to tighten the nut until very snug
    • Tighten up the bottom but and bolt until very snug
    • Repeat process for the other side
  5. step : Reinstalling the Wheel (10:16)
    • Line up the studs and slide the wheel on
    • Thread on the lug nuts by hand to get them started
    • Use the 21mm socket and a torque wrench and torque them to 76 ft-lbs in a star pattern
    • Line up the hubcap and press it back into place
  6. step : Reinstalling Trunk Trim Panels (11:58)
    • Line up the main side trim panel
    • Feed the seatbelt through its special opening
    • Press the tabs of the panel back in place until they lock in
    • Insert the plastic lock back in
    • Reinstall the cargo tie-down hooks and make them snug using a 10mm socket
    • Install side plastic panels
    • Install the cargo bucket and tray
    • Reinstall the trunk floor

Tools needed for replacement:

    Allen Wrenches

  • 5mm Allen Wrench

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 21mm Socket
  • 17mm Socket
  • 18mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 18mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Shocks/struts on 2010 Prius
I just wanted to thank 1A auto for a really great product. I also really appreciate you guys putting out a ‘how to’ video for installation on YouTube. That was super helpful! I had never installed shocks/struts before but your video was very instructive and gave me the confidence I needed. The shocks/struts were of excellent quality and fit my car perfectly . I also bought your control arms and those went in perfectly. That video was also outstanding. Looking forward to more projects. Thanks again!
September 8, 2018
Purchased
2 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2010-2013Toyota Prius Toyota Prius Front & Rear Complete Strut Assembly & Shock Absorber Kit 4 Piece Set

This part replaces:

  • Monroe 172688
  • Monroe 172689
  • Monroe 5685
  • Monroe 5687
  • KYB 349035
  • KYB SR4245
  • KYB SR4246
  • TRQ SK62116
Part #: 1ASSP01655


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: SK62116

How-to Video:

(16:20 min)