Replaces

2009-12 Lexus ES350 Strut & Spring Assembly - 1ASSP01465

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Pre-assembled, loaded strut & spring assemblies allow for a quicker, safer install than replacing with just bare struts. 

Trouble-Free Install

Trouble-free install includes the matched parts needed to get the job done. New mounts, bearings, springs and hardware will provide a better ride for your vehicle and save you time from not having to do the job again because a used part failed afterwards.

Matched Parts

When you buy the kit pre-built by us, you can be sure that the parts are matched for optimum performance.  Not all shocks and struts are manufactured the same, so mixing and matching can result in fit issues and potentially decrease the life of the parts.

Saves Time & Money

When you buy one of our kits, you not only save money over buying the parts individually, but you also save time having to search for all of the different parts that are correct for your vehicle (because we did it for you!)

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:28)
    • Pry off the hub cap with a pry bar
    • Loosen the lug nuts with the vehicle on the ground
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull the wheel off the hub
  2. step : Removing the Sway Bar Link (1:18)
    • Remove the 12mm bolt from the ABS brake line
    • Pry off the plastic clip from the strut
    • Move the caliper and ABS line out of the way
    • Spray rust penetrant on the upper sway bar link nut
    • Clean the upper sway bar link nut with a wire brush
    • Hold the upper sway bar link nut with a 6mm hex socket and breaker bar
    • Loosen the nut with a 17mm wrench
    • If the nut is stuck, hold the sway bar link ball joint with locking pliers if necessary
    • Remove the 17mm nut
    • Move the sway bar out of the strut
  3. step : Removing the Front Strut (3:22)
    • Remove the two lower 22mm strut nuts
    • Remove the bottom bolt and leave the top bolt in
    • Loosen the three outer 14mm nuts from the top of the strut evenly
    • Remove the nuts
    • Lift the strut up and remove the bottom bolt
    • Remove the strut
  4. step : Installing the Front Strut (7:30)
    • Insert the strut into the strut tower
    • Hand-tighten the top 14mm bolts
    • Lift the knuckle into the strut
    • Insert the two bottom 22mm bolts
    • Hand-tighten the bottom nuts
    • Tighten the 15mm nuts on the top of the strut evenly
    • Torque the upper nuts to 63 foot-pounds evenly
    • Tighten the bottom bolts
    • Torque both bolts to 155 foot-pounds while counter-holding
  5. step : Installing the Sway Bar Link (9:59)
    • Slide the sway bar link where it attaches to the strut
    • Tighten the nuts with an 18mm socket and ratchet
    • Torque the 18mm nuts to 55 foot-pounds
    • Tighten the 12mm bolt to the ABS line
    • Clip in the lines to the knuckle
  6. step : Installing the Wheel (11:04)
    • Slide the wheel onto the hub
    • Start the lug nuts by hand, with the tapered side facing the wheel
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts to 76 foot-pounds in a star pattern
    • Line up the hub cap with the valve stem
    • Push the hub cap onto the wheel

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 14mm Socket
  • 15mm Socket
  • 17mm Socket
  • 22mm Socket

  • Wrenches - Metric

  • 22mm Wrench

3.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
0
1
0
0
Ok ride
Ok strut assembly not like the original ride there good for the money you spending but not factor ride if you can spend more money
March 24, 2018
Purchased
1 month ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2009-2012 Lexus ES350 Front & Rear Strut & Spring Assembly 4 Piece Set

This part replaces:

  • Monroe 172310
  • Monroe 172309
  • KYB SR4113
  • KYB SR4112
  • KYB SR4403
  • KYB SR4400
Part #: 1ASSP01465



How-to Video:

(12:38 min)