Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Light uses same wiring as the original assembly, providing easy, trouble-free installation.  No cutting or splicing required.

DOT and SAE Compliant

DOT & SAE compliant: meets federal regulations for on-road use

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Front Bumper (0:24)
    • Place tape along the edge of the bumper to mark its location
    • Remove the 10mm bolts from the splash shield
    • Remove the splash shields
    • Turn the clip in the fender liner on either side
    • Pull back the fender liner
    • Remove the 10mm bolt from the bumper on either side
    • Remove the 10mm bolt from the metal support on top of the bumper
    • Pry up the plastic pin from the headlight with a flat blade screwdriver
    • Remove the Phillips retainer from the bracket
    • Pry up the plastic pin from the headlight with a flat blade screwdriver
    • Pull the bumper off of the bracket
  2. step : Removing the Headlight (6:19)
    • Remove the 10mm bolts from the headlight bracket
    • Pull the headlight out
    • Disconnect the headlight wiring harness
  3. step : Servicing the Bulbs (9:38)
    • Twist the bulb socket counterclockwise out of the light
    • Pull the bulb off of the socket
    • Push on the new bulb
    • Twist the bulb clockwise into the light
  4. step : Installing the New Headlight (11:10)
    • Reconnect the wiring harness to the headlight
    • Line up the bolt holes on the headlight bracket to the bolt holes on the vehicle
    • Replace the 10mm bolts and grommets into the headlight bracket
  5. step : Installing the Front Bumper (13:08)
    • Hang the bumper on the top brackets
    • Push the bumper into the bracket on both sides
    • Press in the push clips to the headlights
    • Tighten the Phillips retainers to the metal bracket
    • Press in the clips to the bumper
    • Tighten the screw to the bumper behind the fender liner on both sides
    • Replace the splash shield
    • Tighten the 10mm bolts to the splash shield

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Painter's Tape

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2009-2010 Toyota Corolla 4 Piece Set Lighting Kit for Models with Chrome Housings

This part replaces:

  • TYC 20-6994-00-1
  • TYC 20-6993-00-1
  • Hollander 114-50727AR
  • Hollander 114-50728AL
  • Hollander 166-50863L
  • Hollander 166-50862R
  • DEPO 312-11A8L-AF1
  • DEPO 312-11A8R-AF1
  • DEPO 312-1992L-AS
  • DEPO 312-1992R-AS
  • OE # 81110-02670
  • OE # 81150-02670
  • OE # 81560-02460
  • OE # 81550-02460
  • Partslink TO2503182
  • Partslink TO2502182
  • Partslink TO2800175
  • Partslink TO2801175
Only 2 left in stock
Part #: 1ALHT00270



How-to Video:

(17:26 min)