Part Details

  • Quantity: Pair

Specifications

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side)
  • Replaces dealer part numbers: 81150-02680, 8115002680, 81110-02680, 8111002680
  • Includes lenses and housings
  • Built to strict quality control standards
  • Correct for models with Black Housing
These headlights are great replacements and have good cost savings over headlights from the dealer.
Fit guaranteed
  • This pair of headlamps will install just as your originals do. You can use your existing hardware and wiring harnesses.
  • Save time and money with a direct fit. No trips to the hardware store or extra time trying to get the wiring to hookup.
Quality
  • 1A Auto has the most comprehensive warranty.
  • If this headlight set should fail to provide satisfactory performance you may exchange it.
  • 1A Auto Headlights are guaranteed to pass inspections in all 50 states. DOT (U.S. Dept. of Transportation) and SAE (Society of Automotive Engineers) approved.
Value
  • Replacing discolored, scratched, dull or damaged headlights with a new pair from 1A Auto can increase your resale value by up to 10%.
Safety
  • A new pair of headlights can provide you with up to 50% more illumination than a dull, yellowed, sandblasted, broken or scratched headlight.
    • 1A Auto headlights can help you see farther at night and in poor driving conditions.
    • A new pair of headlights from 1A Auto can make you more visible to other traffic during heavy rain or wintry weather.
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Bulb Note:

These lights do not include bulbs. Occasionally lighting manufacturers do leave test bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, Parking light, Fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

  1. step : Removing the Front Bumper (0:24)
    • Place tape along the edge of the bumper to mark its location
    • Remove the 10mm bolts from the splash shield
    • Remove the splash shields
    • Turn the clip in the fender liner on either side
    • Pull back the fender liner
    • Remove the 10mm bolt from the bumper on either side
    • Remove the 10mm bolt from the metal support on top of the bumper
    • Pry up the plastic pin from the headlight with a flat blade screwdriver
    • Remove the Phillips retainer from the bracket
    • Pry up the plastic pin from the headlight with a flat blade screwdriver
    • Pull the bumper off of the bracket
  2. step : Removing the Headlight (6:19)
    • Remove the 10mm bolts from the headlight bracket
    • Pull the headlight out
    • Disconnect the headlight wiring harness
  3. step : Servicing the Bulbs (9:38)
    • Twist the bulb socket counterclockwise out of the light
    • Pull the bulb off of the socket
    • Push on the new bulb
    • Twist the bulb clockwise into the light
  4. step : Installing the New Headlight (11:10)
    • Reconnect the wiring harness to the headlight
    • Line up the bolt holes on the headlight bracket to the bolt holes on the vehicle
    • Replace the 10mm bolts and grommets into the headlight bracket
  5. step : Installing the Front Bumper (13:08)
    • Hang the bumper on the top brackets
    • Push the bumper into the bracket on both sides
    • Press in the push clips to the headlights
    • Tighten the Phillips retainers to the metal bracket
    • Press in the clips to the bumper
    • Tighten the screw to the bumper behind the fender liner on both sides
    • Replace the splash shield
    • Tighten the 10mm bolts to the splash shield

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Painter's Tape

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2009-2010Toyota Corolla Toyota Corolla Headlight Pair for Models with Black Housings

This part replaces:

  • Partslink TO2503183, TO2502183
  • OE # 8111002680
  • OE # 8115002680
Part #: 1ALHP00874


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(17:26 min)