2009-10 Nissan Rogue Headlight Pair - 1ALHP01103

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Quantity:   Pair
  • Light Option:   Halogen


  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side)
  • Replaces dealer part numbers: 26010-JM70A, 26060-JM70A, 26010JM70A, 26060JM70A
  • Includes lenses & housings
  • Bulbs not included
  • Fit models with Halogen Headlights only
    • Do NOT fit models with Xenon HID (High Intensity Discharge) Headlights
Fit guaranteed
  • This pair of headlamps will install just as your originals do. You can use your existing hardware and wiring harnesses.
  • Save time and money with a direct fit. No trips to the hardware store or extra time trying to get the wiring to hookup.
  • 1A Auto has the most comprehensive warranty.
  • If this headlight set should fail to provide satisfactory performance you may exchange it.
  • 1A Auto Headlights are guaranteed to pass inspections in all 50 states. DOT (U.S. Dept. of Transportation) and SAE (Society of Automotive Engineers) approved.
  • Replacing discolored, scratched, dull or damaged headlights with a new pair from 1A Auto can increase your resale value by up to 10%.
  • A new pair of headlights can provide you with up to 50% more illumination than a dull, yellowed, sandblasted, broken or scratched headlight.
    • 1A Auto headlights can help you see farther at night and in poor driving conditions.
    • A new pair of headlights from 1A Auto can make you more visible to other traffic during heavy rain or wintry weather.
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Bulb Note:

These lights do not include bulbs.  If you happen to receive a product with bulbs, the bulbs are for testing and not covered under our warranty.  Our warranty applies to the light assembly only.

  1. step : Removing the Bumper (0:52)
    • Remove the eight plastic clips from the top of the bumper with a trim tool
    • Pry the plastic clip from each wheel liner with a trim tool
    • Remove the 10mm bolt inside each wheel liner
    • Remove the six plastic pins from the bottom of the bumper with a trim tool
    • Remove the three T20 Torx bolts from the bottom of the bumper on each side
    • Disconnect the fog light wiring harnesses if you have fog lights
    • Pull the bumper forward and off the vehicle
  2. step : Removing the Headlight (3:10)
    • Remove the three 10mm bolts from the top of the headlight
    • Remove the 10mm nut from the bottom of the headlight
    • Remove the 10mm bolt from the bottom of the headlight
    • Lift the headlight up and off
    • Disconnect the headlight electrical connectors
  3. step : Installing the Headlight (5:09)
    • Connect the headlight electrical connectors
    • Line up the headlight using the stud
    • Install the three 10mm bolts at the top of the headlight
    • Install the 10mm nut at the bottom of the headlight
    • Install the 10mm bolt at the bottom of the headlight
  4. step : Installing the Bumper (5:54)
    • Lift the bumper into place
    • Pop in the bumper tabs
    • Push the eight plastic clips onto the top of the bumper
    • Insert the 10mm bolt inside each wheel well into the bumper
    • Push the wheel liners into place
    • Push the plastic clip into each wheel liner
    • Install the three T20 screws into each side of the bottom of the bumper
    • Line up the bumper with the air dam
    • Insert the six plastic clips into the bottom of the bumper
  5. step : Aiming the Headlights (7:18)
    • Make a dot at the center of your low beam light with a dry erase marker
    • Measure from the ground to the center of the dot
    • Line up your vehicle with a dark flat surface
    • Mark the center of each headlight on the aiming surface
    • Draw a straight line between the two marks
    • back the vehicle up 25 feet from the aiming surface
    • Turn the headlights on
    • Adjust the passenger side aiming screw until the focus of the passenger side light beam is two inches below the line on the aiming surface
    • Adjust the driver side aiming screw until the focus of the driver side light beam is four inches below the line on the aiming surface

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Trim Tool Set

  • Torx Drivers & Sockets

  • T20 Torx Driver

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2009-2010Nissan Rogue Nissan Rogue Halogen Headlight Pair
Part #: 1ALHP01103

Out of Stock

How-to Video:

(09:24 min)