Specifications:

  • Fits LH (Driver Side)
  • Replaces dealer part number: 26060-JM70A, 26060JM70A
  • Includes lens & housing
  • Bulbs not included
  • Fits models with Halogen Headlights only
    • Does NOT fit models with Xenon HID (High Intensity Discharge) Headlights
Fit guaranteed
  • This headlamp will install just as your original does. You can use your existing hardware and wiring harnesses.
  • Save time and money with a direct fit. No trips to the hardware store or extra time trying to get the wiring to hookup.
Quality
  • 1A Auto has the most comprehensive warranty.
  • If this headlight should fail to provide satisfactory performance you may exchange it.
  • 1A Auto Headlights are guaranteed to pass inspections in all 50 states. DOT (U.S. Dept. of Transportation) and SAE (Society of Automotive Engineers) approved.
Value
  • Replacing a discolored, scratched, dull or damaged headlight with a headlight from 1A Auto can increase your resale value by up to 10%.
Safety
  • A new headlight can provide you with up to 50% more illumination than a dull, yellowed, sandblasted, broken or scratched headlight.
    • 1A Auto headlights can help you see farther at night and in poor driving conditions.
    • A new headlight from 1A Auto can make you more visible to other traffic during heavy rain or wintry weather.
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Light uses same wiring as the original assembly, providing easy, trouble-free installation.  No cutting or splicing required.

DOT and SAE Compliant

DOT & SAE compliant: meets federal regulations for on-road use

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

  1. step : Removing the Bumper (0:52)
    • Remove the eight plastic clips from the top of the bumper with a trim tool
    • Pry the plastic clip from each wheel liner with a trim tool
    • Remove the 10mm bolt inside each wheel liner
    • Remove the six plastic pins from the bottom of the bumper with a trim tool
    • Remove the three T20 Torx bolts from the bottom of the bumper on each side
    • Disconnect the fog light wiring harnesses if you have fog lights
    • Pull the bumper forward and off the vehicle
  2. step : Removing the Headlight (3:10)
    • Remove the three 10mm bolts from the top of the headlight
    • Remove the 10mm nut from the bottom of the headlight
    • Remove the 10mm bolt from the bottom of the headlight
    • Lift the headlight up and off
    • Disconnect the headlight electrical connectors
  3. step : Installing the Headlight (5:09)
    • Connect the headlight electrical connectors
    • Line up the headlight using the stud
    • Install the three 10mm bolts at the top of the headlight
    • Install the 10mm nut at the bottom of the headlight
    • Install the 10mm bolt at the bottom of the headlight
  4. step : Installing the Bumper (5:54)
    • Lift the bumper into place
    • Pop in the bumper tabs
    • Push the eight plastic clips onto the top of the bumper
    • Insert the 10mm bolt inside each wheel well into the bumper
    • Push the wheel liners into place
    • Push the plastic clip into each wheel liner
    • Install the three T20 screws into each side of the bottom of the bumper
    • Line up the bumper with the air dam
    • Insert the six plastic clips into the bottom of the bumper
  5. step : Aiming the Headlights (7:18)
    • Make a dot at the center of your low beam light with a dry erase marker
    • Measure from the ground to the center of the dot
    • Line up your vehicle with a dark flat surface
    • Mark the center of each headlight on the aiming surface
    • Draw a straight line between the two marks
    • back the vehicle up 25 feet from the aiming surface
    • Turn the headlights on
    • Adjust the passenger side aiming screw until the focus of the passenger side light beam is two inches below the line on the aiming surface
    • Adjust the driver side aiming screw until the focus of the driver side light beam is four inches below the line on the aiming surface

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Trim Tool Set

  • Torx Drivers & Sockets

  • T20 Torx Driver

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2009-2010 Nissan Rogue Halogen Headlight Driver Side

This part replaces:

  • Partslink NI2502204
  • Hollander 114-50807L
  • OE # 26060JM70A
  • TYC 20-12392-00
  • DEPO 315-1167L-AFN
Only 3 left in stock
Part #: 1ALHL02263



How-to Video:

(09:24 min)