Replaces
Part Details
Handle is the original color shade.
Pro Tip: Replace Handles in pairs or sets. Fading from the sun or age can make your Vehicle Handles and Bezels appear a hue difference next to new Handles.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks!
In this video, we're going to show you how to replace the rear outside door handles on this 2007 Denali. It's the same process for any 2007 to 2013 Yukon Denali, as well as the SLT, and Tahoe LTZ. It's also probably the same procedure or a similar procedure for rear doors on the Yukon XL, Suburban, as well as the four-door Sierra and Silverados with the LTZ Denali or SLT trims.
Items you'll need include handles from 1AAuto.com, small and regular flat blade screwdrivers, 10mm socket with ratchet and extension, and a door panel clip tool or putty knife.
Disconnect the battery. You want to open up the driver's door, pull the hood release lever, hit the safety hatch, move it to the right, and then lift the hood up, and the battery is near the rear of the engine compartment on the passenger side. There's a 10mm nut on top of the negative battery cable. Loosen that 10mm nut and pull the battery cable up and off, and then put it to the side so it won't contact the terminal again.
Open up either rear door. The procedure is the same for both. You need a small flat blade screwdriver, and you'll pry out that square clip, pry out this panel under here, and I am just using one hand, so it does drop to the ground, one hand holding the camera, one hand working the screwdriver. Then there is also a little panel underneath here that you pry out. Once you have that panel out, it'll expose a 10mm bolt there, and then there's another 10mm bolt to remove down here.
Use a small screwdriver and pull up on the walk knob and pry that clip out, and it comes up and off. I'll fast-forward here as I remove those two 10mm bolts. Use a plastic trim tool or a rag and a flat blade screwdriver, and pry up on the switch panel. You kind of pry up in the center and then you pull it up and it locks. The clips are on the front and the rear. Once you get the center up, you just kind of work it into the front, and then work it into the rear. It comes up and off and then the harness just has a tab on it. You press the tab and unplug it.
Use a rag to protect your paint and a door panel clip tool, or you could use a putty knife, but you work either the tool or the knife in underneath the clip. You'll basically feel that you slide it through and you can feel the plastic clips, and then you pull out and release the clips, and I usually do this for two or three of the clips on the back side. Then you can work your hand underneath and release the rest of the clips.
Once the clips are released, you pull the panel up and off of the window ledge clip. If your door panel has never been off before, the water shield, the white water shield you can see is a black clip holding it to the door panel. There's probably three or four of these little black clips. You can see how you try to use the clip tool or a screwdriver to pry the clip out. Eventually, I just end up grabbing ahold of the clip and the water shield at the same time and pull them out. Again, you'll have to do this probably three or four times if your door panel has never been off before.
We'll need to undo the door handle cable clip. There's two little clips that hold the cable in. I'm just prying with a small screwdriver to release those clips. Here's a better shot of them as they come out. You pull it out and up out of the handle, and then the door panel comes right off.
There are three 7mm bolts to remove on the backside of the handle. Two of them hold the handle to the door panel. One of them holds the switch to the handle. We'll speed up here as I just remove those three 7mm bolts.
With the bolts out, you can press lightly on the back and you'll release a bottom clip. Then there's a couple clips at the top. Use a flat blade screwdriver. Just pry lightly between the handle and the top of the door panel and push out at the same time to release the door handle. Then pull the door handle out.
We already removed the 7mm bolt that holds the switch into the handle. If not, remove that, then the switch pulls right out.
New handle, put the switch back into place and then put that 7mm bolt that holds it, goes at the top of the switch on the backside, then tighten that up. Be careful not to over-tighten. You want to get it nice and firm, but you don't want to over-tighten it and strip the plastic threads.
The handle goes back into the door. Feed the harness through. Then it snaps into place. Then put the two 7mm bolts that hold it and tighten them up. Again, just tighten them firm. Don't over-tighten.
To reinstall the door panel, get it close, put the ball of the cable into the door handle, then pull the cable around and clip it in. Move the panel close to the door, make sure that the harness comes up through, and then make sure that the door lock goes up through the hole there, and then you kind of lift the panel up and push the top on and set it down into that window ledge clip, and then you can kind of look in behind, make sure that the clips line up. Once you have everything lined up, then you can reset the clips.
Make sure that you pull the lock knob up and then put the lock trim on there. Set that, make sure you leave it unlocked, and then reinstall the two 10mm bolts that hold the panel in place. I'll fast forward as I do that. When you tighten these, tighten them up firm, you don't want to tighten them, though, and make sure you have the harness pulled up through, put the two trim pieces in place. The upper one, you want to put the rear end first and then snap the front end. It snaps in at the front first on me, so I have to pull it back out, and then put it in correctly. Again, the back towards the back goes in first, and then front snaps in, and then reconnect the harness and snap the switch panel down in place, and then do a little test.
Then reconnect your battery, then you should be all good to go. Put the negative battery cable back on the post and 10mm socket, ratchet, and extension, then tighten it up.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
