Replaces

2007-11 Toyota Camry Window Regulator Front Passenger Side - 1AWRG01471

This replacement window regulator is just what you need to get your vehicle in good shape again!

Specifications:

  • RH (Passenger Side) FRONT
  • Does NOT include the power window motor
  • Replaces dealer part numbers: 69801-06070, 6980106070
  • Power operation
  • Direct replacement
  • Built to strict quality control standards
  • Fits US Built models only
    • US built vehicles have a 1,2, or 4 for the first digit of the VIN (Vehicle Identification Number)

This window regulator makes a great replacement and has good cost savings over a dealer unit.

 

 

Please Note: This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original.  It has been subjected to extensive testing and quality control standards.  That is why we offer this regulator with our superior warranty!

Installation

  • This repair is easier than you may think. You'll find our installation videos helpful. In our experience removing and replacing the door panel is the most involved step in the repair. On most vehicles this only requires removing a few screws and push in clips.
  • You'll get a great feeling of accomplishment after you complete this repair knowing you saved money, and you didn't have to give up your car for a day at the repair shop. Your passengers and other drivers will be amazed.

Fit guaranteed

  • 1A Auto will refund you with no hassle, if this Window regulator does not fit the application stated.
    •  This Regulator will install just as your original does. Save time and money.

Quality

  • Be confident this part will work right. Every regulator is tested after assembly to make sure all mechanisms are working correctly.
  • It is important that your new regulator works for a long period of time. The design of this regulator is tested to withstand 10,000 cycles. That is enough to raise and lower your window 3 times per day for 9 years.
  • Nothing is more frustrating than taking your car apart and finding the part you purchased does not fit. You want the part to fit. This design is test fit on an actual door. When you install it, you will have no issues.

Value

  • Windows that don't work can be frustrating. They can also hurt your vehicles value. An inoperable window could mean $200-$500 discounted off a dealer trade value or asking price.
  • Some shops and dealers charge more for parts and repairs when they think you don't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly repair bill.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Door Panel (0:19)
    • Pry the courtesy light out of the door panel with a trim tool
    • Disconnect the courtesy light electrical connector
    • Pry the trim piece off the mirror base with a trim tool
    • Pry the grab handle panel off the door handle with a trim tool
    • Pry the trim piece out of the door handle with a trim tool
    • Pry the clip out of the front of the door panel with a trim tool
    • Remove the Phillips screw inside the door handle
    • Remove the two Phillips screws from the grab handle
    • Pry out the door panel clips by hand
    • Lift the door panel off the door
    • Unclip the door lock cable from the door handle
    • Pop the door handle out of the door
    • Disconnect the wiring harness from the door panel
    • Unclip the wiring harness from the door panel
    • Disconnect the door latch cable from the door handle
  2. step : Removing the Water Shield (3:08)
    • Pull off the water shield
    • Remove the wire from the clips
    • Disconnect the wiring harnesses
    • Slide the wiring through the water shield
  3. step : Removing the Door Speaker (6:54)
    • Remove the four Phillips screws from the speaker
    • Slide the speaker out of the door
  4. step : Removing the Window Regulator (7:06)
    • Disconnect the window motor lead
    • Loosen the two 10mm bolts that hold the window to the regulator
    • Raise the window by hand
    • Hold the window in place with painter's tape
    • Remove the five 10mm bolts from the regulator
    • Pull the window regulator out through the door
  5. step : Reinstalling the Regulator (8:33)
    • Insert one of the bolts into the window regulator
    • Push the regulator into the door
    • Hang the regulator by its bolt
    • Insert the four 10mm bolts into the regulator
    • Remove the painter's tape from the window
    • Lower the window onto the regulator
    • Insert the two 10mm bolts that hold the window to the regulator
  6. step : Installing the Door Speaker (10:41)
    • Slide the speaker into the door with the electrical connector at the top
    • Insert the four Phillips screws into the speaker
    • Connect the speaker electrical connector
  7. step : Installing the Water Shield (11:15)
    • Slide the wiring and cables through
    • Press the shield to the door
    • Press the wire into its clips
    • Plug in the wiring harnesses
  8. step : Installing the Door Panel (14:29)
    • Clip the white door cable into the top of the door handle
    • Clip the green door cable into the bottom of the door handle
    • Feed the courtesy light electrical connector through the door panel
    • Connect the electrical connector to the door panel
    • Clip the door handle into the door panel
    • Lift the door panel onto the door
    • Line up the door panel, using the locating pins
    • Push in the door panel clips
    • Insert the Phillips screw inside the door handle
    • Clip the trim into the door handle
    • Insert the two Phillips screws into the grab handle
    • Clip the trim onto the grab handle
    • Clip the trim piece onto the mirror base
    • Push the plastic clip into the front of the door panel
    • Connect the courtesy light electrical connector
    • Push the courtesy light into the door panel

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Gloves
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Side Cutters

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver
  • T25 Torx Driver

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(18:15 min)

Tools List:

    Materials, Fluids, and Supplies

  • Gloves
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Side Cutters

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver
  • T25 Torx Driver



This part replaces:

  • Hollander 125-50189
  • OE # 6980106070
  • Dorman 749-233

Vehicle Fit

  • 2007-2011 Toyota Camry Power Window Regulator (US Built Models) Front Passenger Side (High Quality)
Part #: 1AWRG01471

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More