Replaces

2007-11 Honda CR-V Strut & Spring Assembly TRQ SCA57203 - 1ASSP01107

Part Details

  • Quantity: 4 Piece Set

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:48)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Front Strut and Spring Assembly (1:28)
    • Place a 17mm wrench on the upper sway bar link nut
    • Grab the sway bar link joint with a 6mm allen wrench and socket
    • Loosen the 17mm nut with a socket and ratchet
    • Remove the sway bar link from the strut
    • Pry the ABS sensor wire out of its retainer in the strut
    • Remove the 12mm bolt on the brake line brace
    • Remove the two 22mm lower strut bolts with a 19mm wrench and 22mm socket and breaker bar
    • Tap the bolts out with a hammer and punch if needed
    • Peel back some weatherstripping from the cowl panel
    • Undo the cover on the cowl panel
    • Loosen the 14mm nuts on top of the strut
    • Remove the nuts with a magnet
    • Remove the strut
  3. step : Installing the Front Strut and Spring Assembly (8:52)
    • Reinstall the strut into the vehicle
    • Hand-tighten the top nut
    • Torque the upper nuts to 33 foot-pounds
    • Replace the cowl cover
    • Replace the weatherstrip
    • Insert the steering knuckle into the strut
    • Tighten the lower bolts with a 19mm socket and ratchet
    • Torque the bolts to 116 foot-pounds
    • Reinstall the brake hose into the retainer
    • Tighten the 12mm bolt to the retainer
    • Pop the ABS sensor into the bracket
    • Reinstall the sway bar link into the strut
    • Grab the sway bar link joint with locking pliers and a 6mm allen wrench and socket
    • Tighten the 17mm nut with a socket and ratchet
  4. step : Reattaching the Wheel (14:16)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts in a crossing or star pattern to 80 foot-pounds

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Magnet - Extendable
  • Center Punch
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 17mm Socket
  • 19mm Socket
  • 22mm Socket

  • Specialty Tools

  • Trim Tool Set

  • Wrenches - Metric

  • 17mm Wrench
  • 18mm Wrench

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
Honda CRV Struts
First time to order automotive parts online, parts arrived three days later as promised. Exact fit no modifications needed.
This has given me the confidence in mail-order parts. I would recommend 1Aauto to everyone.
September 19, 2018
Purchased
3 weeks ago
Great Service
I got my order much earlier than expected. They are reliable and offer great prices.

Many thanks!
March 9, 2018
Purchased
7 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 3 answers
good day this kit brings the shock absorbers?
Diego S on Mar 29, 2018
BEST ANSWER: Yes, the assembly includes the struts (shock absorbers) and the coil springs.

Vehicle Fit

Year Make Model Description
2007-2011Honda CR-V Honda CR-V Front & Rear Strut & Spring Assembly 4 Piece Set TRQ SCA57203

This part replaces:

  • Hollander 527-50267R
  • Hollander 527-50268L
  • Hollander 527-50269R
  • Hollander 527-50270L
  • Hollander 527-60692R
  • Hollander 527-60693L
  • Monroe 272492
  • Monroe 272491
  • Monroe 172497L
  • Monroe 172497R
  • KYB SR4244
  • KYB SR4243
  • TRQ SCA57203
Part #: 1ASSP01107


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: SCA57203

How-to Video:

(15:13 min)