This replacement Tail light is just what you need to get your vehicle in good looking form again!

This tail lamp features the following specifications:

  • LH (Driver Side)
  • Replaces dealer part numbers: 81561-33490, 8156133490
  • Includes lens & Housing
  • DOT (Department of Transportation) & SAE (Society of Automotive Engineers) approved
  • Direct replacement
  • Correct for Hybrid Models only

This tail light makes a great replacement and has good cost savings over a dealer unit.

Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Part Details

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

  1. step : Removing the Rear Bumper (0:26)
    • Remove the Phillips screw from the access hole in the wheel well liner
    • Remove the screw beneath the fender liner
    • Remove the screws from underneath the bumper
    • Open the trim buttons on the bumper
    • Remove the 10mm bolts from the bumper
    • Mark the bumpers position with tape
    • Pull out the bumper from the side
    • Separate the bumper from the rear
  2. step : Removing the Tail Light (3:46)
    • Pull back the carpet trim in the trunk
    • Remove the 10mm bolts from the tail light
    • Turn the bulb sockets counterclockwise to remove them from the light
    • Slide the tail light out
  3. step : Installing the Tail Light (6:18)
    • Press the tail light into the car
    • Turn the bulb sockets clockwise to stick them in the light
    • Tighten the 10mm bolts to the light
    • Press on the carpet trim
  4. step : Installing the Rear Bumper (8:38)
    • Lift the bumper onto the rear
    • Line up the slots with the holes on the bumper
    • Push the bumper into place
    • Tighten the 10mm bolts to the bumper
    • Press on the trim button to the bumper
    • Tighten the screw beneath the fender liner
    • Tighten the Phillips screw though the access hole in the wheel well liner

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Painter's Tape

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Wrenches - Metric

  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
does this light have the 9 LED's for the tail light and brake light?
neil d on Mar 22, 2017
BEST ANSWER: From our image we may see at least 6 LEDs. We may have our stock inspected once the part is back in stock to confirm the exact number however if you would like. Please call us at 1-888-844-3393 if you would like to have this set up.

Vehicle Fit

  • 2007-2009 Toyota Camry Hybrid Tail Light Driver Side

This part replaces:

  • OE # 8156133490
  • Partslink TO2804103
  • Hollander 166-50379BL
  • DEPO 312-1982L-UF
Only 3 left in stock
Part #: 1ALTL01398

How-to Video:

(10:37 min)