Replaces

2006-12 Honda Civic Wheel Bearing & Hub Assembly Pair TRQ BHA53570 - 1ASHS00462

Specifications:

  • Come as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) REAR
  • Replaces dealer part number: 42200-SNC-951, 42200SNC951
  • 4 Bolt Flanges
  • Fit 5 Lug Wheels
  • Studs already installed
  • Direct replacements
  • Built to strict quality control standards

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hubs & bearings are all tested prior to shipping.

Fit Guaranteed

  • These hub & bearing sets will install just as your originals do. You can use your existing hardware.
  • Save time and money with direct fit hub bearing assemblies. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.
Precision Engineered

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement

Guaranteed to fit and function correctly for your specific application.

Part Details

  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:27)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads and Brake Rotor (0:49)
    • Remove the 12mm bolt from the brake line
    • Remove the 12mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the brake pad slides
    • Clean the slides with a wire brush
    • Apply anti-seize fluid or white grease to the slides
    • Push the slides on with a flat blade screwdriver
    • If only changing the pads, continue to Step 6 and install the new pads
    • Remove 14mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Slide the wheel speed sensor wire out of the bracket
    • Remove the 10mm bolt from the wheel speed sensor
    • Remove the wheel speed sensor
    • Thread a lug nut onto the rotor
    • Hold the rotor with a pry bar
    • Remove the Phillips screws from the rotor
    • Pull the rotor off
    • If the rotor will not come off, thread the lug nuts and strike the hub area of the rotor with a rubber mallet
  3. step : Removing the Wheel Hub (6:27)
    • Remove the 14mm bolts from behind the hub
    • Remove the hub
  4. step : Installing the Wheel Hub (8:45)
    • Insert the hub into place
    • Tighten the 14mm bolts to the wheel hub
    • Torque the bolts to 47 foot-pounds
  5. step : Installing the New Brake Pads and New Brake Rotor (9:23)
    • Clip the speed sensor into the bracket
    • Install the speed sensor into the hub
    • Tighten the 12mm bolt to the sensor
    • Clean the rotor with brake parts cleaner or mineral spirits
    • Slide the rotor on
    • Tighten the Phillips screws to the rotor
    • Put the caliper bracket onto the rotor
    • Tighten the caliper bracket bolts to 54 foot-pounds of torque
    • Start the bolts by hand
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Place anti-seize grease onto the brake pad tabs
    • Coat the brake pad material with brake parts cleaner
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread 17mm bolts by hand
    • Tighten bolts to 17 foot-pounds
  6. step : Reattaching the Wheel (12:45)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 79.6 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Rubber Mallet
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner
  • Paper Towels
  • Bungee Cord
  • Anti-Seize Grease

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 19mm Socket
  • 10mm Socket

  • Specialty Tools

  • Dead Blow Hammer

  • Wrenches - Metric

  • 17mm Wrench
  • 12mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2006-2012 Honda Civic GX CNG Rear Wheel Bearing & Hub Assembly Pair TRQ
  • 2006-2012 Honda Civic Hybrid Rear Wheel Bearing & Hub Assembly Pair TRQ

This part replaces:

  • OE # 42200-SNC-951 x2
  • TRQ BHA53570
Part #: 1ASHS00462

TRQ
Brand #: BHA53570

How-to Video:

(13:33 min)