Replaces

2006-11 Honda Civic Strut & Spring Assembly TRQ SCA57706 - 1ASTS01163

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Part Details

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:26)
    • Loosen the lug nuts with the vehicle on the ground with a 17mm socket and breaker bar
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Strut (0:57)
    • Press the tabs and remove the ABS wire bracket from the strut
    • Remove the bolt on the brake line bracket with a 12mm wrench
    • Loosen the strut nuts with a 19mm socket and a breaker bar
    • Remove the lower bolts
    • Lift up on the weatherstripping and pop open the cowl door
    • Remove the three nuts from the top of the strut with a 14mm socket
    • Remove the bolt from the bottom of the strut
    • Lower the strut down and out
  3. step : Installing the Strut (5:42)
    • Insert the strut up into place
    • Line up the bolt holes with the knuckle
    • Thread a nut on top by hand
    • Insert two lower strut bolts by hand
    • Tighten the three nuts to the top of the strut with a 14mm socket and ratchet
    • Torque the top nuts to 33 foot-pounds
    • Replace the cowl panel door and weatherstrip
    • Tighten the lower bolts with a 17mm socket and ratchet
    • Torque the bolts to 67 foot-pounds
    • Insert the brake line in place and tighten the 12mm bolt
    • Clip in the ABS wire
  4. step : Reattaching the Wheel (8:54)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • Swivel
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 12mm Socket
  • 17mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 12mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2006-2011 Honda Civic Sedan Front Strut & Spring Assembly Passenger Side (excluding SI Models) TRQ SCA57706

This part replaces:

  • Monroe 172286
  • KYB SR4241
  • TRQ SCA57706
Part #: 1ASTS01163


Order must be placed by 4pm ET
TRQ
Brand #: SCA57706

How-to Video:

(09:33 min)