Replaces

2006-11 Honda Civic Steering & Suspension Kit - 1ASFK05281

 

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:28)
    • Loosen the lug nuts with a 19mm socket with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Front Sway Bar Links (0:57)
    • Clean off any rust from the nut with a wire brush
    • Spray the rusty parts with rust penetrant
    • Break the nuts free with a 14mm wrench
    • To reach the upper nut, raise a jack underneath the control arm
    • Counter-hold with a 5mm Allen bit
    • Remove the nut with a 14mm wrench
    • Lower the jack
    • Counter-hold with a 5mm Allen key
    • Remove the lower nut with a 14mm wrench
  3. step : Installing the Front Sway Bar Links (5:27)
    • Insert the sway bar link into place
    • Tighten the nuts with a 17mm wrench
    • Counter-hold with a 5mm Allen bit
  4. step : Reattaching the Wheel (6:47)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    Allen Wrenches

  • 5mm Allen Wrench

  • General Tools

  • Jack Stands
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 19mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 17mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2006-2011 Honda Civic excluding SI Models 6 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K80769
  • Moog K80768
  • Moog EV800246
  • Moog ES800374
  • Moog ES800373
  • OE # 51321SNAA02
  • OE # 51320SNAA02
  • OE # 53010SNEA01
Part #: 1ASFK05281



How-to Video:

(07:26 min)