Replaces

2006-11 Honda Civic Shock Absorber Pair TRQ SBA60320 - 1ASSP00740

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   Pair

Our direct fit gas-charged shock absorbers help to restore your vehicle’s handling and ride quality to just like new.

Direct Fit

Fits and functions correctly.  Competitors combine applications to reduce the amount of parts they carry, resulting in: incorrect vehicle height, poor response and an uncomfortable ride.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Interior Trunk Trim (0:25)
    • Remove the three pins from the side interior trim panel in the trunk
    • Lift the flooring
    • Remove the pin from the side interior trim panel in the trunk
    • Remove the trim panel from the ledge
    • Move the side interior trim out of the way
    • Remove the 14mm nut from the shock with a 5mm allen key and 14mm wrench
    • Remove the plates from the shock
  2. step : Removing the Wheel (3:01)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. step : Removing the Rear Shock Absorber (3:25)
    • Support the lower control arm with a floor jack
    • Remove the lower bolt with a 14mm socket and breaker bar
    • If the bolt snaps, remove it with a hammer and punch
    • Wedge the shock out with a pry bar
    • Remove the shock
  4. step : Installing the Rear Shock Absorber (6:55)
    • Remove the nuts and rubber bushings from the top of the shock absorber
    • Place a washer on the stud of the shock absorber
    • Place a bushing on the washer
    • Place a casing on the stud
    • Insert the shock up into place
    • Press the bolt through the bottom of the shock
    • Thread the nut on to the bolt
    • Jack up underneath the control arm to press the shock into place
    • Place a bushing on the top of the shock
    • Place a washer on the top of the bushing
    • Tighten the 14mm bolt to the top of the shock
    • Torque the bolt to 22 foot-pounds
  5. step : Installing the Interior Trunk Trim (10:14)
    • Insert the interior trunk trim into place
    • Press the trunk hatch trim on
    • Place the flooring on
    • Press the push clips into the interior trunk trim
    • Jack up underneath the shock
    • Torque the bolt to 43 foot-pounds, counter-holding if needed
  6. step : Reattaching the Wheel (12:02)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    Allen Wrenches

  • 5mm Allen Wrench

  • General Tools

  • Hammer
  • Jack Stands
  • Center Punch
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Side Cutters

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 14mm Wrench

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Good replacement product!
Replaced my leaking shocks and these went right on without too much issue. The only issue i had during install was cranking down the bolts on top. I didnt have a good tool to hold the bolt to keep it from spinning when tightening the nut down. I tried a small wrench, but it kept slipping off as I got tighter. I managed to get it tight enough and it seems to be fine(no noise coming from there).
August 25, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2006-2011Honda Civic Honda Civic Rear Shock Absorber Pair TRQ SBA60320
Part #: 1ASSP00740


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: SBA60320

How-to Video:

(12:50 min)