Replaces

2006-11 Honda Civic Rear Shock Absorber Set TRQ SBA60320 - 1ASSP00740

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Our direct fit gas-charged shock absorbers help to restore your vehicle’s handling and ride quality to just like new.

Direct Fit

Fits and functions correctly.  Competitors combine applications to reduce the amount of parts they carry, resulting in: incorrect vehicle height, poor response and an uncomfortable ride.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Interior Trunk Trim (0:25)
    • Remove the three pins from the side interior trim panel in the trunk
    • Lift the flooring
    • Remove the pin from the side interior trim panel in the trunk
    • Remove the trim panel from the ledge
    • Move the side interior trim out of the way
    • Remove the 14mm nut from the shock with a 5mm allen key and 14mm wrench
    • Remove the plates from the shock
  2. step : Removing the Wheel (3:01)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. step : Removing the Rear Shock Absorber (3:25)
    • Support the lower control arm with a floor jack
    • Remove the lower bolt with a 14mm socket and breaker bar
    • If the bolt snaps, remove it with a hammer and punch
    • Wedge the shock out with a pry bar
    • Remove the shock
  4. step : Installing the Rear Shock Absorber (6:55)
    • Remove the nuts and rubber bushings from the top of the shock absorber
    • Place a washer on the stud of the shock absorber
    • Place a bushing on the washer
    • Place a casing on the stud
    • Insert the shock up into place
    • Press the bolt through the bottom of the shock
    • Thread the nut on to the bolt
    • Jack up underneath the control arm to press the shock into place
    • Place a bushing on the top of the shock
    • Place a washer on the top of the bushing
    • Tighten the 14mm bolt to the top of the shock
    • Torque the bolt to 22 foot-pounds
  5. step : Installing the Interior Trunk Trim (10:14)
    • Insert the interior trunk trim into place
    • Press the trunk hatch trim on
    • Place the flooring on
    • Press the push clips into the interior trunk trim
    • Jack up underneath the shock
    • Torque the bolt to 43 foot-pounds, counter-holding if needed
  6. step : Reattaching the Wheel (12:02)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Center Punch
  • Floor Jack

  • Hex Wrenches

  • 5mm Hex Wrench

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Side Cutters

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 14mm Wrench

4.40/ 5.0
5 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
1
1
0
0
Good replacement product!
Replaced my leaking shocks and these went right on without too much issue. The only issue i had during install was cranking down the bolts on top. I didnt have a good tool to hold the bolt to keep it from spinning when tightening the nut down. I tried a small wrench, but it kept slipping off as I got tighter. I managed to get it tight enough and it seems to be fine(no noise coming from there).
August 25, 2017
Excellent quality for the price everything was exactly like the video thank you
January 2, 2019
Purchase review
Write your review here. It must be at least 4 characters long. Consider whether you would recommend this proGood afternoon, The shocks I ordered are now squeaking. The rubber isolators did not match up to stock on the top mounts. Had I known you had KYB, I would have purchased them instead, but, the KYB choice did not pull up when I searched. Only after poking around on the site and searching for front struts did I see that I could search under KYB as a manufacturer. So, I guess I’m stuck with the squeaky cheap Chinese rear shocks. Btw, I am diy. Your videos and delivery were fine. Thank-you, Duaneduct and what you like or dislike about it.
August 9, 2019
As good as brand name shocks
I recently bought a set of brand name shocks for a different vehicle, and I can contest that these TRQ shocks from 1A Auto perform just as good for less money.
October 16, 2019
2006 Honda Civic Shocks
The shocks were much better quality than the car’s stock shocks. The order arrived very quickly and on time. The price was also cheaper than my local auto parts store.
October 31, 2019
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2006-2011Honda Civic Honda Civic Rear Shock Absorber Set
Part 1ASSP00740
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: SBA60320