Replaces

2006-11 Honda Civic A/C Condenser Cooling Fan Assembly - 1AACF00074

Our aftermarket A/C condenser fan assemblies are some of the highest quality replacements on the market! This AC condenser cooling fan assembly is a complete, ready to bolt on, direct replacement part.

Specifications:

  • Fits RH (Passenger Side)
  • New, not rebuilt, electric motor
  • Geometrically designed plastic blade for optimal circulation and uniform balance
  • Shroud designed to ensure structural integrity and endurance for maximum performance
  • 100% Performance factory tested
  • Replaces original assemblies that are melted or worn out
  • Comes with proper plug(s) for trouble free installation
  • Replaces dealer part number: 38616-RNA-A01, 38616RNAA01

Now you can buy a high quality AC Condenser cooling fan motor assembly that is built to strict quality control standards. This cooling motor assembly makes a great replacement and has substantial cost savings over a dealer fan assembly.

 

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

 

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Radiator Shield (0:20)
    • Pop and secure the hood
    • Pry off the push clips from the shield
    • Remove the shield
  2. step : Disconnecting the Cooling Fan (2:13)
    • Unplug the A/C and radiator cooling fan's wiring harness
    • Press the tabs and release the wire from the fan bracket
    • Pop the clip out of the radiator bracket
  3. step : Removing the Battery (4:02)
    • Remove the 10mm negative battery terminal
    • Remove the 10mm positive battery terminal
    • Loosen the 10mm battery hold down bolts
    • Lift the battery hold down out without touching the terminals
    • Remove the plastic cover from the battery
    • Lift the battery up and out
  4. step : Removing the Radiator Support (6:18)
    • Disconnect the electrical connector from the fan
    • Unclip the connector from the fan
    • Pop the radiator hose out of the bracket
    • Pry off the overflow hose from the filler neck
    • Unbolt the two 10mm bolts from the filler neck
    • Remove the two T30 Torx bolts from the grille
    • Remove the 10mm bolt from the A/C condenser bracket
    • Remove the two 10mm bolts from the A/C top bracket
    • Remove the three 10mm bolts on each side of the radiator support ends
    • Remove the temp sensor wiring harness clips from the radiator support
    • Lift the radiator support out of the way
  5. step : Removing the A/C Condenser Cooling Fan (11:41)
    • Remove the 10mm bolts from the a/c condenser fan
    • Lift the fan up and out of the radiator
  6. step : Installing the A/C Condenser Cooling Fan (12:33)
    • Insert the fan into place
    • Tighten the 10mm bolts to the cooling fan
  7. step : Reinstalling the Radiator Support (13:18)
    • Insert the radiator support into place
    • Clip in the wiring harness bracket
    • Clip in the fan wiring harness
    • Connect the coolant overflow hose to the filler neck
    • Clip in the hose to the overflow bottle
    • Tighten the bolts to the overflow neck
    • Connect the wiring harness clips to the fan
    • Tighten the 10mm bolts to the upper radiator mounts
    • Tighten the 10mm bolts to the bushings
    • Tighten the T30 Torx bolts to the grille mount
    • Tighten the three 10mm bolts to either end of the radiator support
  8. step : Reinstalling the Radiator Shield (18:26)
    • Insert the radiator shield into place
    • Press the clips in to the radiator shield
  9. step : Reinstalling the Battery (19:37)
    • Place the battery cover on
    • Insert the battery into place
    • Hook in the battery hold down
    • Tighten the 10mm battery hold down bolts
    • Connect the positive terminal and tighten the 10mm bolt
    • Connect the negative terminal and tighten the 10mm bolt

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 17mm Socket
  • 10mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

  • Wrenches - Metric

  • 17mm Wrench
  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2006-2011 Honda Civic A/C Condenser Cooling Fan Assembly L4 1.8L Passenger Side

This part replaces:

  • OE # 38616RNAA01
  • Partslink HO3115129
  • Hollander 674-50122
  • TYC 610970
  • DEPO 317-55028-200
Only 1 left in stock
Part #: 1AACF00074

How-to Video:

(21:14 min)