Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
TRQ side mirrors and mirror components are designed to match the function, fixture, and performance of the original version for easy installation. TRQ mirrors are DOT certified, comply with all federal safety standards, and are independently lab tested to ensure our products comply with all government regulations. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Exact fit - To obtain proper fit and function confirm your vehicle has the exact mirror options listed.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality auto replacement parts and the bets service on the internet.
In this video, we're going to show you how to replace a side view mirror on this 2008 Chevy HHR, same as any '06 to 2010. Tools you'll need are a small flat blade screwdriver, a T30 Torx driver, a putty knife or a door panel clip tool. Those three things just get your door panel off. Then you'll need a 10 millimeter wrench or an socket and ratchet.
First, look down inside your pull cap here. You'll see a little tab. Grab the tab, pull up the little rubber plate. Then there's two T30 Torx screws in there. Then take a little screwdriver. Pry out underneath this little tee point here. Then a T30 Torx screw on there. Use a little fast motion here as I remove those three T30 screws. Right down here's a little pin. Just kind of pry it out with a screwdriver. Okay. Take a putty knife first. Put it back in there. Pull. Use a door panel clip tool if you like. Find the rest of the pins. You can kind of look in there at the same time. Actually, what I eventually found on this is it's actually easy once you get the door panel out a little bit. Just run your fingers underneath the door panel until you come to one of the clips and then give it a good pull and it comes off.
I'm going to pull this down just a little bit. Here's our connection for the mirror. I'll pry out. You can either use your fingernail or a screwdriver. A little tab. Pry out and disconnect that. Three 10mm bolts here. You can use a socket and ratchet. A wrench will work fine. We'll hit a little high speed here as we just remove those three nuts. Okay. The mirror comes off. Pull out the harness. Okay. New mirror from 1A Auto. Has the chrome back and everything which is correct for this vehicle. We're just going to pull this out here. We can put the mirror in place. We use our original bolts. Hit a little fast motion here again. Put those three 10mm nuts on there and then tighten them up with our socket and ratchet and extension. Don't over tighten them. Just you want to tighten them up nice and firm.
Then connect our lead right there. Put that back. Okay. We'll kind of fast forward through putting the door panel back on there. If you want to see this in regular speed, just check out our other videos but you can probably get pretty much everything you need. Put the lock switch back on there. Put the cable back on for the door handle. Put it into place. Make sure you get the tongue on the top to go down into the clips. Then peek in, make sure the clips all wind up. Push it onto the door panel. Then put your three T30 Torx screws back in and your trim plates back on.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality auto replacement parts and the bets service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that serve you on the internet and in person.
Tools used
