Specifications

  • LH (Driver Side)
  • Replaces dealer part numbers: 33151-S9V-A11, 33151S9VA11
  • Includes lens and housing
  • Bulbs not included
  • Direct replacement for halogen style headlight
Fit guaranteed
  • This headlamp will install just as your original does. You can use your existing hardware and wiring harnesses.
  • Save time and money with a direct fit. No trips to the hardware store or extra time trying to get the wiring to hookup.
Quality
  • 1A Auto has the most comprehensive warranty.
  • If this headlight should fail to provide satisfactory performance you may exchange it.
  • 1A Auto Headlights are guaranteed to pass inspections in all 50 states. DOT (U.S. Dept. of Transportation) and SAE (Society of Automotive Engineers) approved.
Value
  • Replacing a discolored, scratched, dull or damaged headlight with a headlight from 1A Auto can increase your resale value by up to 10%.
Safety
  • A new headlight can provide you with up to 50% more illumination than a dull, yellowed, sandblasted, broken or scratched headlight.
    • 1A Auto headlights can help you see farther at night and in poor driving conditions.
    • A new headlight from 1A Auto can make you more visible to other traffic during heavy rain or wintry weather.
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Light uses same wiring as the original assembly, providing easy, trouble-free installation.  No cutting or splicing required.

DOT and SAE Compliant

DOT & SAE compliant: meets federal regulations for on-road use

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly.

  1. step : Removing the Bumper Cover (0:17)
    • Open the hood
    • Remove the thirteen clips from the radiator cover
    • Remove the radiator cover
    • Remove the push clip from the grille on either side
    • Remove the Phillips head screw at the corner of the bumper in each wheel well
    • Remove the two 10mm bolts from the bottom of the bumper on either side
    • Release the clips from the splash shield
    • If needed remove the eleven push clips and Phillips screws from the mud guard
    • Pry out the side of the bumper from the bracket
    • Unclip the bumper from its brackets
    • Lift the bumper up and off
    • Disconnect the fog light connectors
    • Pry the fog light harness from its bracket
    • Remove the bumper
  2. step : Removing the Headlight (10:30)
    • Remove the three 10mm bolts from the headlight
    • Unclip the push clip from the headlight
    • Disconnect the bulb connector
    • Disconnect the harness underneath the headlight
    • Pry the headlight straight out
    • Disconnect the bulb connector
  3. step : Servicing the Bulbs (15:26)
    • Press the clip and slide the connector off
    • Twist the bulb socket counterclockwise out of the light
    • Pull the bulb off of the socket
    • Push on the new bulb
    • Twist the bulb clockwise into the light
  4. step : Installing the Headlight (18:32)
    • Insert the headlight into place
    • Press the tabs on the headlight into the fender
    • Tighten the three 10mm bolts to the headlight
    • Connect the bulb connectors
    • Push on the push clips
    • Test the lights
  5. step : Installing the Bumper Cover (23:55)
    • Lift the bumper into place
    • Connect the fog light wiring harness
    • Align the bumper with the brackets
    • Press the bumper into the bracket
    • Press in the push clips to the top of the grille
    • Lift the splash shield underneath the bumper
    • Connect the clips to the splash shield
    • Tighten the 10mm bolts to the splash shield
    • Align the mud guards and press in the 11 clips if needed and Phillips screws
    • Tighten the Phillips screw to the corner of each wheel well
    • Press on the radiator cover
    • Press on the thirteen clips to the radiator cover

Tools needed for replacement:

    General Tools

  • Assistant

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2006-2008 Honda Pilot Headlight Driver Side

This part replaces:

  • OE # 33151S9VA11
  • Partslink HO2518110
  • Hollander 114-50151L
  • TYC 20-6760-01-1
  • DEPO 317-1149L-UF2
Part #: 1ALHL01463



How-to Video:

(31:15 min)