Replaces

2005-09 Subaru Legacy Outback Rear Driver or Passenger Side Wheel Bearing & Hub Assembly Timken HA590119 - TKSHR00145

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

TIMKEN WHEEL BEARING & HUB ASSEMBLY: HA590119

This replacement wheel bearing & hub assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits LH (Driver Side) or RH (Passenger Side) REAR
  • Replaces dealer part number: 28473AG00B, 28473AG00A
  • 4 Bolt Flange
  • Fits 5 Lug Wheel
  • New wheel studs installed
  • Direct replacement
  • Built to strict quality control standards

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (0:27)
    • Loosen the lug nuts with a 19mm socket and breaker bar
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull the wheel off the studs
  2. step : Removing the Brake Pads (1:25)
    • Loosen the two slide bolts from the caliper with a 14mm wrench
    • Remove the slide bolts
    • Compress the brake pad into the piston with a flat blade screwdriver
    • Swing the caliper around and off the brake pads
    • Remove the brake pads from the caliper bracket with a flat blade screwdriver
    • Remove the two 19mm bolts from the caliper bracket
    • Pull the caliper bracket off
    • Remove the brake rotor
  3. step : Removing the Axle Nut (4:11)
    • Insert a punch into the axle nut
    • Tap the bunch with a hammer to release the nut
    • Remove the center cap from the wheel
    • Place the wheel onto the hub and secure the lug nuts by hand
    • Lower the vehicle to the ground
    • Secure the rotor with a pry bar
    • Loosen the 32mm axle nut
    • Raise and support the vehicle
    • Remove the lug nuts
    • Remove the wheel
  4. step : Removing the Hub (6:36)
    • Remove the 10mm bolt from the speed sensor
    • Pry the sensor up
    • Remove the four 14mm bolts from behind the wheel bearing
    • Pull the hub out
    • Tap the hub out from the backing shield a rubber mallet if needed
  5. step : Installing the Hub (11:00)
    • Clean off the mating surface with rust penetrant and a wire brush
    • Insert the hub into place
    • Gently tap the hub into place with a rubber mallet
    • Gently tighten the bolts
    • Torque the bolts 47.9 foot-pounds
    • Place the wheel onto the hub and secure the lug nuts by hand
    • Lower the vehicle to the ground
    • Tighten the axle nut
    • Torque the axle nut to 177 foot-pounds
    • Raise and support the vehicle
    • Remove the lug nuts
    • Remove the wheel
    • Insert the speed sensor into place
    • Tighten the 10mm bolt to the sensor
  6. step : Installing the Brake Rotor (14:32)
    • Slide the rotor backwards onto the hub
    • Spray the rotor with brake parts cleaner and a rag
    • Turn the rotor over and spray the front with brake parts cleaner
    • Slide the rotor onto the hub
  7. step : Installing the Brake Pads (15:03)
    • Line up the caliper bracket on the wheel
    • Start the 19mm bolts for the caliper bracket
    • Torque the caliper bracket bolts to 47.9 foot-pounds
    • Clean the brake pads with brake parts cleaner
    • Apply caliper grease to the brake pad ears
    • Place the brake pads into the caliper bracket
    • Pull the bungee cord off the brake caliper
    • Put an old brake pad in the caliper
    • Compress the caliper piston with the old brake pad and a C-clamp
    • Swing the caliper onto the caliper bracket
    • Insert the bolts into the caliper
    • Torque the slide bolts to 19 foot-pounds
    • Tap the axle nut down into the axle divot with a hammer and punch to secure it
  8. step : Installing the Wheel (18:51)
    • Slide the wheel onto the studs
    • Start the lug nuts by hand
    • Lower the vehicle to the ground
    • Torque the lug nuts to 90 foot-pounds
    • Pump the brake pedal until the brakes feel firm

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bungee Cord
  • Anti-Seize Grease

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 10mm Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2005-2009Subaru Legacy Subaru Legacy Rear Driver or Passenger Side Wheel Bearing & Hub Assembly
2005-2009Subaru Outback Subaru Outback Rear Driver or Passenger Side Wheel Bearing & Hub Assembly
Part #: TKSHR00145

Out of Stock

Timken
Brand #: HA590119