Brake Pad Specifications:

  • Professional grade Ceramic Enhanced brake pads
  • 8 Piece Front & Rear brake pad set
  • Includes shims
  • Direct replacements

Brake Rotor Specifications:

  • Comes as a Set of 4
    • Includes both LH (Driver Side) & RH (Passenger Side) Front & Rear
  • Cross drilled, Slotted, And Zinc Coated
  • Direct replacements
  • Fits 5 Lug Wheels
  • Front 11.69" (297mm) diameter
  • Rear 10.63" (270mm) diameter
Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

Zinc Coated

Zinc Coated to help reduce rust and corrosion for a longer-lasting and better looking rotor

"True" Non-Interference Vane Design

"True" Non-Interference Vane Design retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots are machined to remove brake dust and expel gasses during hard braking

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel and tire (1:30)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Remove Caliper (2:00)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 15mm socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
  3. step : Remove brake disk (2:44)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Remove Hub (2:56)
    • Remove the 3 bolts securing the hub using your 13mm socket and 3/8 extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Use a rubber mallet to break it free, and work around the flange with the hammer to pull it off.
    • Leave the top 13mm loosely still in to prevent the hub from flying out if you hit it too hard.
    • Remove the hub, using driving tools to help work it out of the steering knuckle.
    • Clean up any corrosion with a wire brush.
  5. step : Install new hub (8:30)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Watch part 2 to install your new 1A Auto hub!

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Rubber Mallet

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 19mm Socket
  • 32mm Socket
  • 35mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
front and rear rotors and pads
The parts I received appeared to be good quality. I just installed them this past weekend (10/16/17) and there better than the brakes I had on my car before. Unless something goes terribly wrong I'll be buying my next set from A-1.
October 19, 2017
Purchased
7 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004 Pontiac Grand Prix (excluding GXP Models) Front & Rear Ceramic Cross Drilled & Slotted Zinc Coated Performance Brake Kit
Part #: 1APBS00771


How-to Video:

(09:37 min)