2004-15 Toyota Prius Window Regulator - 1AWRX00002

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Regulator Option:   without Motor
  • Operation:   Power

This replacement power window regulator without motor is just what you need to get your vehicle in good shape again!


  • RH (Passenger Side) REAR DOOR
  • Replaces dealer part number: 69801-52070, 6980152070
  • Power operation
  • Direct replacement
  • Built to strict quality control standards
  • Does not include motor
    • Buyer will need to reuse original motor

This  power window regulator without motor makes a great replacement and has good cost savings over a dealer unit.

Please Note:

This window regulator is designed to work with factory style motors only.  Due to variations in aftermarket designs, replacement motors may not have the correct gear style.

Please Note:

This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original. It has been subjected to extensive testing and quality control standards. That is why we offer this regulator with our superior warranty!

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Rear Door Panel (0:21)
    • Pry off the door pull trim
    • Lift up the rear window switch
    • Disconnect the wiring harness
    • Pry up the door pull felt
    • Remove the Phillips screw from the door pull
    • Pry out the trap door from the door handle
    • Remove the Phillips screw from the door handle
    • Pry the door panel out of the clips with a trim tool
    • Pop the door handle out of the clips
    • Remove the door panel
  2. step : Removing the Inner Door Handle (3:33)
    • Remove the cables from the inner door handle
    • Slide the cables' lead ball out of the lock and handle
  3. step : Removing the Vapor Barrier (3:55)
    • Remove the 10mm bolts from the bracket
    • Remove the bracket
    • Disconnect the door lock actuator electrical connector
    • Disconnect the window motor electrical connector
    • Disconnect the speaker electrical connector
    • Pry out the harnesses from their clips
    • Peel off the water vapor barrier with a razor
  4. step : Removing the Window Regulator (8:17)
    • Disconnect the window motor connector
    • Remove the 10mm bolts from the window
    • Lift the window up
    • Secure the window in place with painter's tape
    • Loosen a 10mm bolt for the regulator to hang on
    • Remove the five 10mm mounting bolts from the window regulator
    • Remove the window regulator
  5. step : Removing the Window Motor (11:04)
    • Remove the T25 Torx screws from the motor
    • Remove the motor
  6. step : Installing the Window Motor (11:40)
    • Insert the motor into place
    • Tighten the T25 Torx screws to the motor
  7. step : Installing the Window Regulator (12:10)
    • Insert one of the bolts into the window regulator
    • Push the regulator into the door
    • Hang the regulator by its bolt
    • Insert the five 10mm bolts into the regulator
    • Remove the painter's tape from the window
    • Lower the window onto the regulator
    • Insert the two 10mm bolts that hold the window to the regulator
  8. step : Installing the Vapor Barrier (15:58)
    • Line the vapor barrier into place
    • Press the vapor barrier into place
    • Press the harnesses into their clips
    • Connect the door lock actuator electrical connector
    • Connect the window motor electrical connector
    • Connect the speaker electrical connector
    • Insert the bracket into place
    • Tighten the 10mm bolts to the bracket
  9. step : Installing the Inner Door Handle (18:17)
    • Connect the cables to the inner door handle
  10. step : Installing the Rear Door Panel (18:42)
    • Connect the interior door handle to the door panel
    • Slide the door panel on to the windowsill
    • Press the door panel in to the door
    • Tighten the Phillips screw to the door handle
    • Reinstall the door handle trim piece
    • Reinstall the screw in the door pull
    • Press on the door pull felt
    • Connect the wiring harness to the window switch
    • Press the window switch into place
    • Press the door pull trim on to the door

Tools needed for replacement:

    General Tools

  • Razor Blade / Gasket Scraper

  • Materials, Fluids, and Supplies

  • Gloves

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Trim Tool Set

  • Torx Drivers & Sockets

  • T30 Torx Driver
  • T25 Torx Driver

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2004-2015Toyota Prius Toyota Prius Rear Power Window Regulator without Motor Passenger Side
Part #: 1AWRX00002

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(20:43 min)