Replaces

2004-09 Toyota Prius Tie Rod - 1ASTE00844

Select Your Vehicle to Verify Fit for our 1A Auto Fit Guarantee
04-09 Toyota Prius Front Inner Tie Rod End LF = RF

Specifications:

  • Brand New Tie Rod End
  • Fits LH (Driver Side) or RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:24)
    • Pry off the hub cap with a pry bar
    • Loosen the lug nuts with the vehicle on the ground
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull the wheel off the hub
  2. step : Removing the Sway Bar Link (1:15)
    • Spray rust penetrant on the upper sway bar link nut
    • Clean the upper sway bar link nut with a wire brush
    • Hold the upper sway bar link nut with a 6mm hex socket and breaker bar
    • Loosen the nut with a 17mm wrench
    • If the nut is stuck, hold the sway bar link ball joint with locking pliers if necessary
    • Remove the 17mm nut
    • If the nut remains stuck, cut the sway bar link stud with a hack saw or reciprocating saw
    • Hold the lower sway bar link ball joint with locking pliers
    • Remove the 17mm bolt from the lower sway bar link stud
    • Remove the sway bar link from the vehicle
  3. step : Installing the Sway Bar Link (7:54)
    • Hang the sway bar link where it attaches to the strut
    • Slide the sway bar link stud into sway bar
    • Start the 18mm nuts onto the sway bar link studs by hand
    • Hold the sway bar link ball joints with an 18mm wrench
    • Tighten the nuts with an 18mm socket and ratchet
    • Torque the 18mm nuts to 55 foot-pounds
  4. step : Installing the Wheel (8:52)
    • Slide the wheel onto the hub
    • Start the lug nuts by hand, with the tapered side facing the wheel
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts to 76 foot-pounds in a star pattern
    • Line up the hub cap with the valve stem
    • Push the hub cap onto the wheel

Tools needed for replacement:

    Allen Wrenches

  • 6mm Allen Wrench

    • General Tools

  • Jack Stands
  • Sawzall
  • Wire Brush
  • Floor Jack

    • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Brake Parts Cleaner

    • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

    • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

    • Screwdrivers & Related

  • Pry Bar

    • Sockets - Metric

  • 17mm Socket
  • 18mm Socket
  • 21mm Socket

    • Wrenches - Metric

  • 17mm Wrench
  • 18mm Wrench
  • 21mm wrench

Powered by TurnTo
There are no reviews for this item. Write Review
Powered by TurnTo
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004-2009 Toyota Prius Front Inner Tie Rod Driver or Passenger Side

This part replaces:

  • Moog EV80304
  • Beck Arnley 101-5431
  • OE # 4550347030
  • OE # 4550347030, 45503347030
1
Part #: 1ASTE00844

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(10:10 min)