Replaces

2004-09 Nissan Quest Brake & Wheel Bearing Kit - 1ABMS00089

Brake Pad Specifications:

  • Premium Posi Ceramic Brake Pad
  • 4 Piece front brake pad set
  • Includes shims
  • Direct replacements

Brake Rotor Specifications:

  • Comes as a Pair
    • Fits both LH (Driver Side) & RH (Passenger Side) Front
  • Fits 5 Stud Wheels
  • 11.4"(290mm) diameter
  • Vented

Wheel Bearing & Hub Assembly Specifications:

  • Comes as a Pair
    • Fits both LH (Driver Side) & RH (Passenger Side) Front
  • 4 Bolt Rectangular Flange
  • Fits 5 Lug Wheel
  • Direct replacements
  • Built to strict quality control standards

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quiet braking
Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

100% CNC-Machined to Exact OE Specs

100% CNC-Machined to exact OE specs and balanced to reduce vibration

Cast from OE Grade Alloy

Manufactured from OE Grade G3000 Casting Alloy

Non-Directional Surface Finish

Non-Directional Rotor Surface Finish helps ensure smoother, quieter, and more effective braking

Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:54)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
    • If necessary, kick the tire to loosen the wheel
  2. step : Inspecting the Brakes (1:30)
    • Turn the rotor by hand or turn the steering wheel to turn the rotor
    • Check the thickness of the brake pads
    • Check the brake pad wear indicator
    • Check for gouges on both sides of the rotor
  3. step : Removing the Brake Pads (2:12)
    • Remove the two 14mm bolts from the brake caliper
    • Pull the caliper aside
    • Pull off the brake pads by hand
  4. step : Removing the Brake Rotor (3:22)
    • Remove the two 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Remove the screws from the brake rotor with an impact screwdriver
    • If you cannot remove the screws, drill them out
    • Pull the rotor off
  5. step : Installing the New Brake Rotor (5:58)
    • Slide the rotor on
    • Insert the screws into the new rotor
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Check that the caliper slides move freely
    • Clean the brake pad slides with a wire brush
    • Put the bracket back into place
    • Start the two 18mm bolts by hand
    • Tighten the 18mm bolts to between 85 - 90 foot-pounds of torque
  6. step : Installing the New Brake Pads (7:44)
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten the 14mm bolts to between 18 - 20foot-pounds
    • Clean the rotor with brake parts cleaner or mineral spirits
  7. step : Reattaching the Wheel (9:07)
    • Turn the rotor straight
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 95 - 100 foot-pounds in a crossing or star pattern
  8. step : Testing the Brakes (9:44)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    Drills, Drill Bits & Related

  • 1/4 Inch Drill Bit
  • Drill

  • General Tools

  • Floor Jack
  • Large C-Clamp
  • Jack Stands
  • Hammer

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench
  • 1/2 Inch Breaker Bar
  • Ratchet

  • Screwdrivers & Related

  • Impact Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 19mm Socket
  • 18mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004-2009 Nissan Quest Front Premium Posi Ceramic Brake & Wheel Bearing Kit

This part replaces:

  • Reference Number CD855
  • Reference Number 513310
  • Hollander 538-58993
  • OE # 40202-ZM70A
Part #: 1ABMS00089


How-to Video:

(10:17 min)