Replaces

2004-09 Mazda 3 Windshield Washer Reservoir - 1AWWR00060

Our windshield washer reservoirs are some of the highest quality replacements on the market! This windshield washer bottle has been designed to replace the original designs.

Specifications:

  • Brand New Washer Bottle
  • Includes washer motor with 2 pin connector
  • Direct replacement
  • Replaces dealer part numbers: BN8V-67480-D, 13502353
  • Not correct for models with Low Fluid Sensor

Now you can buy a high quality windshield washer reservoir that is built to strict quality control standards. REPLACE your broken or cracked one now with this great fitting washer tank.

Part Details

  • Includes: Washer Pump

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Bumper Cover (0:43)
    • Remove the two clips in both front wheel wells.
    • Remove the eight â€" ten 10mm bolts from under the bumper cover.
    • Pull the inner fender back and remove the bolt up inside the fender.
    • Remove the two Phillips screws at the top of the bumper cover.
    • Remove the Phillips head clips.
    • Pull up and out on the clips behind the grill.
    • Pull the bumper cover free.
    • Unclip the wire harnesses from the back of the bumper cover.
  2. step : Remove the Passenger Side Headlight (3:27)
    • Remove the two 10mm bolts on the sides of the headlight.
    • Remove the 10mm bolt at the top of the light using a wrench and socket.
    • Remove the Phillips clip at the top of the headlight.
    • Pull the light free.
    • Disconnect the clips on the back of the light.
    • Twist and pull out side marker light.
  3. step : Removing the Washer Bottle (4:57)
    • Drain the bottle by removing the connections.
    • Remove the cap to help it drain.
    • Spray penetrating oil on the three bolts securing the bottle.
    • Remove the three bolts.
    • Using pliers pull the clip securing the wiring harness.
  4. step : Replacing the Washer Bottle (6:07)
    • Line up the bottle and snap it into place.
    • Screw in the three bolts to secure the bottle.
    • Reinstall the grommet and washer pump to the bottle.
    • Reattach the wiring harness and hose.
    • Fill the washer bottle.
  5. step : Replace the Headlight (7:45)
    • Reconnect the three wiring harnesses.
    • Line up the pins on the light with the holes on the body.
    • Replace the clip.
    • Reinsert the three bolts to secure the headlight.
  6. step : Reattach the Bumper Cover (8:36)
    • Plug in the wiring harnesses.
    • Line the bumper cover up with the car.
    • Lock the two clips in place on the back of the grill
    • Snap the sides into place.
    • Reinsert the two screws and clips at the tops of the bumper cover.
    • Reinsert the two 10mm bolts inside the inner fender.
    • Reinsert the eight â€" ten 10mm bolts into the bottom of the bumper cover.
    • Reinsert the clips in the wheel wells.

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Wrenches - Metric

  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004-2009 Mazda 3 Sedan Windshield Washer Reservoir with Washer Pump without Low Fluid Sensor

This part replaces:

  • OE # 13502353
  • OE # BN8V67480D
  • Hollander 627-50598
  • Dorman 603-045
Part #: 1AWWR00060

How-to Video:

(10:29 min)