2004-08 Chrysler Pacifica Window Regulator - 1AWRG01182

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Regulator Option:   with Motor
  • Operation:   Power


  • Fits LH (Driver Side) Rear
  • Power operation
  • Includes the power window motor

Please Note:

This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original. It has been subjected to extensive testing and quality control standards. That is why we offer this regulator with our superior warranty!

Direct Fit

Direct fit, pre-assembled parts made ready to fit your vehicle and provide easy and trouble-free installation.

Rigorously Tested

Build to strict quality standards

Highest Quality Materials

Made from the highest quality materials for extreme durability and premium performance.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (0:42)
    • Pry off the trim piece inside the door handle with a flat blade screwdriver
    • Pry off the trim piece inside the door pull with a flat blade screwdriver
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw inside the door pull
    • Pry out the door panel with a door panel clip tool or putty knife
    • Lift the door panel up and off
    • Disconnect the window switch wiring harness
    • Disconnect the latch cables from the door handle
    • Remove the Phillips screws from the door panel brackets
    • Pull off the door panel brackets
    • Remove the three Phillips screws from the speaker
    • Pull out the speaker
    • Disconnect the speaker wiring harness
    • Carefully peel off the water shield
  2. step : Removing the Window Regulator (3:19)
    • Disconnect the window motor wiring harness
    • Separate the window from the regulator with a flat blade screwdriver
    • Raise the window by hand
    • Hold the window in place with painter's tape
    • Loosen the top two 10mm bolts from the regulator
    • Remove the lower 10mm bolt from the regulator
    • Pull the window regulator out through the door
  3. step : Installing the Regulator (6:13)
    • Remove the two top 10mm bolts from the old regulator
    • Thread the top two 10mm bolts onto the new regulator
    • Push the regulator into the door
    • Hang the regulator by its bolts
    • Tighten the top two 10mm bolts into the regulator
    • Insert the bottom 10mm bolt into the regulator
    • Lower the window onto the regulator
    • Snap the window into the regulator
    • Connect the window motor wiring harness
  4. step : Reinstalling the Door Panel (7:50)
    • Put the water shield into place
    • Connect the speaker wiring lead
    • Put the speaker into place
    • Insert the three Phillips screws into the speaker
    • Put the door panel bracket into place
    • Insert the Phillips screws into the brackets
    • Connect the window switch wiring harness
    • Connect the latch cables to the door handle
    • Lift the door panel into place
    • Push in the door panel clips
    • Insert the Phillips screw into the door handle
    • Insert the Phillips screw into the door pull
    • Push on the trim piece inside the door handle
    • Push in the door pull trim piece

Tools needed for replacement:

    General Tools

  • Putty Knife
  • Flashlight

  • Materials, Fluids, and Supplies

  • Painter's Tape

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Door Panel Removal Tool

  • Wrenches - Metric

  • 10mm Wrench

4.67/ 5.0
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Very happy with my parts ordered they arrived on time and were a prefect fit, With no problems.
January 24, 2017
One word- AMAZING
Cant even begin to describe how pleased I am with my purchase and the how to video. Took me literally minutes to install a new window regulator. The price? PHENOMINAL difference from everyone else. Ill be getting one for my Silverado soon as well!
February 22, 2017
Nearly perfect fit. Overall good
The only issue I had is one of the three bolts (upper most bolt) interfered with the window carrier bracket, preventing the winow from rolling all the way up, leaving about a quarter inch gap. After inserting a spacer, works perfectly. Easy to install.
July 30, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2004-2008Chrysler Pacifica Chrysler Pacifica Rear Power Window Regulator with Motor Driver Side
Part #: 1AWRG01182

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(10:43 min)