Replaces

2004-08 Chrysler Pacifica Brake Rotor Front Pair Nakamoto 53019-DSZ - 1APBR00324

Specifications:

  • Comes as a matched Pair
    • Includes LH (Driver Side) & RH (Passenger Side) Front
  • Cross drilled, Slotted, And Zinc Coated
  • Direct replacement
  • Fits 5 Stud Wheels
  • 12.52" (318mm) diameter
Zinc Coated

Helps reduce rust and corrosion for a longer-lasting and better looking rotor.

"True" Non-Interference Vane Design

Retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots remove brake dust and expel gasses during hard braking.

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power.

Part Details

  • Front or Rear Location: Front
  • Brake Rotor Coating: Zinc Coated
  • Brake Rotor Type: Cross Drilled & Slotted
  • Quantity: Pair
  • Front Brake Rotor Specifications: Vented
  • Front Brake Rotor Specifications: 5 Lug
  • Front Brake Rotor Specifications: 12.52" (318mm)
  • Product Line: Performance

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:45)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:11)
    • Check for gouges on both sides of the rotor
    • Check the thickness of the brake pads
    • Check the brake pad wear indicator
  3. step : Removing the Brake Pads (1:51)
    • Turn the rotor by hand or turn the steering wheel to turn the rotor
    • Pry the pads into the caliper with a flat blade screwdriver or a pry bar
    • Remove the two 14mm bolts from the brake caliper
    • Pry the caliper off with a flat blade screwdriver
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  4. step : Removing the Brake Rotor (3:41)
    • Remove the two 21mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
  5. step : Installing the New Brake Rotor (4:29)
    • Clean the brake pad slides with a wire brush
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Put the bracket back into place
    • Start the two 21mm bolts by hand
    • Tighten the bolts to 110 foot-pounds of torque
    • Check that the caliper slides move freely
    • If they do not move freely, apply grease
  6. step : Installing the New Brake Pads (6:26)
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten the 14mm bolts to between 22 - 25 foot-pounds
  7. step : Reattaching the Wheel (8:27)
    • Remove the placeholder lug nut
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  8. step : Testing the Brakes (9:04)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Wire Brush
  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 21mm Socket
  • 14mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2004-2008Chrysler Pacifica Chrysler Pacifica Cross Drilled & Slotted Brake Rotor Front Pair Zinc Coated Performance Nakamoto

This part replaces:

  • Nakamoto 53019-DSZ
Part #: 1APBR00324


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Nakamoto
Brand #: 53019-DSZ

How-to Video:

(09:32 min)