Part Details

  • Light Option: Halogen


  • RH Passenger Side
  • Replaces dealer part number: 26010-ZA80A
  • Includes lens and housing
  • Bulbs not included
  • Halogen Style
    • Not correct for Xenon (HID) lights

    Due to changes in the manufacturing process, these housings use H9 bulbs for the low beams instead of the factory 9012. There are no modifications required and the factory wiring will fit correctly without issue

Fit guaranteed

  • This headlamp will install just as your original does. You can use your existing hardware and wiring harnesses.
  • Save time and money with a direct fit. No trips to the hardware store or extra time trying to get the wiring to hookup.


  • 1A Auto has the most comprehensive warranty.
  • If this headlight should fail to provide satisfactory performance you may exchange it.
  • 1A Auto Headlights are guaranteed to pass inspections in all 50 states. DOT (U.S. Dept. of Transportation) and SAE (Society of Automotive Engineers) approved.


  • Replacing a discolored, scratched, dull or damaged headlight with a headlight from 1A Auto can increase your resale value by up to 10%.


  • A new headlight can provide you with up to 50% more illumination than a dull, yellowed, sandblasted, broken or scratched headlight.
    • 1A Auto headlights can help you see farther at night and in poor driving conditions.
    • A new headlight from 1A Auto can make you more visible to other traffic during heavy rain or wintry weather..
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Item Condition: New

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Bulb Note:

Unless otherwise noted, our lights do not include bulbs, though occasionally lighting manufacturers do include bulbs in the lights. If you happen to receive a lighting product (Headlight, Tail light, parking light, fog light etc.) that comes with the bulbs, the bulbs are not covered under our warranty. Our warranty applies only to the light assembly..

  1. step : Removing the Bumper Cover (0:51)
    • Remove the two black clips from both sides of top of the bumper.
    • Remove the two Phillips screws underneath the bumper in front of the wheels.
    • Pull the inner fender back.
    • Find the wiring harness inside the fender and pull the tab to disconnect it.
    • Remove the two 10mm bolts inside the inner fender.
    • Remove the series of six pins underneath the front bumper.
    • Pull firmly on each side and lift and pull the bumper cover forward.
  2. step : Removing the Headlight (3:49)
    • Remove the five 10mm bolts around the headlight.
    • Pull the light forward, up and out.
    • Press firmly on the tab and pull the wiring harness free.
  3. step : Changing Headlight Bulb (4:40)
    • Turn headlight cap counterclockwise and pull out.
    • Press the locks in towards the center of the light.
    • Pull the bulb out. (Do not touch the glass of the new bulb).
    • Press down and turn counterclockwise to free the old bulb.
    • Push new bulb in and turn clockwise
    • Put socket into place and latch the locks.
    • Reapply headlight cap by lining up tabs and locking it into place.
  4. step : Changing Turn Signal Bulb (6:10)
    • Twist the socket counterclockwise to release it.
    • Push bulb down and out.
    • Push new bulb in.
    • Turn clockwise to lock.
  5. step : Changing Fog Light (6:32)
    • Twist socket cap counter clockwise and pull out.
    • Push latch on light down and pull the socket free.
    • Free bulb from cap.
    • Carefully pull the bulb free.
    • Push new bulb into place and reconnect to cap.
    • Line the round cut out with the bottom and place the socket into place.
    • Bring the latch down to lock it.
    • Twist the cap clockwise to lock.
  6. step : Replacing the Headlight Assembly and Bumper Cover (8:31)
    • Reconnect the light harness and line up the headlight.
    • Lock it into place and reinsert the five 10mm bolts.
    • Test Headlight.
    • Line up the bumper cover and push it into place.
    • Push the two clips back in on top.
    • Lift the bottom panel up and over. Replace the six clips.
    • Reach up into the fender and replace the two bolts.
    • Reinstall the wiring harness.
    • Reinstall the Phillips screws under bumper cover.

Tools needed for replacement:

    General Tools

  • Flashlight

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2004-2006Nissan Maxima Nissan Maxima Halogen Headlight Passenger Side

This part replaces:

  • Hollander 114-59173R
  • TYC 20-6521-90-1
  • DEPO 315-1149R-ASN7
  • OE # 26010ZA80A
Only 2 left in stock
Part #: 1ALHL01349

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(12:37 min)