Specifications:

  • Brand New Performance Cold Air Intake Kit
  • Polished 6061 aluminum tubing
  • 3" (76.2mm) diameter piping
  • Blue cone air filter
  • Includes all necessary couplers, clamps, brackets, and hardware to install
  • Built to strict quality control standards

Due to state emissions regulations, we cannot ship this item to the state of California as it is not C.A.R.B ( California Air Research Board) approved for use in this state.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Air Intake (0:46)
    • Release the clips and open the air filter housing box
    • List the air filter housing box cover up and off
    • Release the PCV hose
    • Loosen the rear clamp on the inlet pipe
    • Remove the box cover and pipe
    • Lift the bottom of the air filter housing box up and out
    • Remove the 10mm bolt behind the alternator
    • Remove the 10mm bolt behind the oil cap
    • Lift the air box up
    • Disconnect the intake sensor
    • Remove the air box
  2. step : Preparing the Performance Intake Kit (2:07)
    • Press the thinner end of the gasket onto the heat shield around the bends
    • Remove the rubber bushings from the air box
    • Press the rubber bushings into the Z and medium-sized L Bracket
    • Press the Z bracket onto the bottom of the heat shield
    • Insert the 11mm bolts and washers to Z bracket and shield
    • Tighten the bolts loosely
    • Insert the 11mm bolts and washer to the medium L bracket and shield
    • Tighten the bolts loosely
    • Press the 11mm rubber insulated nut to the short twisted bracket and tighten it
    • If your truck has an EGR, use the long, straight bracket
    • If your truck does not have EGR, use the long, twisted bracket
    • Place the intake tube collar and space onto the single drilled hole of the bracket
    • Insert the washer and 11mm nut to the bottom of the bolt
    • Support the other end of the bolt with a 4mm Allen lock key
    • Tighten the 11mm nut loosely
    • Press the rubber grommet to the air intake tube
    • Remove the air intake temp sensor from the air box
    • Remove the O-ring from the air sensor if you have it
    • Press the air sensor into the rubber grommet on the air intake tube
  3. step : Installing the Heat Shield (6:53)
    • Remove the 13mm bolt from the fan shroud just below the radiator fill
    • Insert the bolt to the bigger slotted hole on the small L bracket by hand
    • Remove the 13mm bolt behind the hood strut on the air box bracket
    • Insert the slotted hole on the twisted bracket with the rubber insulated nut to the air box
    • Tighten the 13mm bolt to the bracket
    • Insert and press the heat shield into place
    • Insert the shorter hardware into the insulated nut
    • Insert the hardware to the small L bracket
    • Tighten all the bolts
  4. step : Installing the Intake Hose, Filter, and PCV Hose (9:26)
    • Remove the clamp from the PCV breather hose
    • Install the silicone cuppling with the hose clamps to the throttle body
    • Tighten the throttle body-side hose clamp with a flat blade screwdriver
    • Insert the intake tube bracket to the front bolt that held the upper air box
    • If your vehicle does not have an EGR, read the instructions to find appropriate bracket placement
    • Test-fit the intake tube
    • Tighten the bolt to the bracket
    • Insert the hose clamp over the intake tube and insert the tube into place
    • Tighten the hose clamp near the heat shield with a flat blade screwdriver
    • Reconnect the IAT sensor
    • Insert the intake cone onto the intake tube
    • Tighten the hose clamp near the throttle body
    • Insert the PCV breather into the slot below the oil fill neck
    • Insert the PCV breather to the fitting on the intake hose
    • Tighten the clamps with needle nose pliers
    • Turn on the engine to make sure everything's working

Tools needed for replacement:

    Allen Wrenches

  • 4mm Allen Wrench

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 11mm Socket
  • 10mm Socket
  • 13mm Socket

  • Wrenches - Metric

  • 11mm Wrench
  • 13mm Wrench
  • 10mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Solid product
I just received this tonight and started the install around 8 and was done by 10. I would have been done sooner but because this doesn't come with a heat shield (which shouldn't come as a shock for the price) I had to do some fabrication in order to fit It into my factory air box. (I didnt want it just sitting in my engine bay) I'm hopeful I'll see a difference in performance and fuel mileage.
September 26, 2017
Purchased
8 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Does this kit come with a heat shield like the video shows?
James B on Sep 20, 2017
BEST ANSWER: This specific kit does not include a heat shield, but you may make one to work with this set.

Vehicle Fit

  • 2003-2008 Dodge Ram 1500 Truck Performance Air Intake Kit with Blue Filter V8 5.7L
  • 2003-2008 Dodge Ram 2500 Truck Performance Air Intake Kit with Blue Filter V8 5.7L
  • 2003-2008 Dodge Ram 3500 Truck Performance Air Intake Kit with Blue Filter V8 5.7L
Part #: 1APAI00187


How-to Video:

(12:30 min)