Replaces

2003-07 Honda Accord Front Driver Side Strut & Spring Assembly TRQ SCA57506 - 1ASTS00657

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (0:27)
    • Partially raise the vehicle with the wheel still contacting the ground
    • Loosen the 19 mm lug nuts
    • Raise and support the vehicle on jack stands
    • Remove the lug nuts
    • Replace one lug nut loosely
    • Hammer the tire from the back side if the wheel is stuck
    • Remove the last lug nut and the wheel
  2. step : Removing the Strut (0:55)
    • Remove the 14 mm lower strut bolt
    • Remove the 17 mm nut from the 17 mm wishbone bolt and remove the bolt
    • Remove the wishbone from the bottom of the strut
    • Remove the three 14 mm and two 12 mm nuts from the top strut mount
    • Remove the strut from the top mount
    • Remove the upper control arm cotter pin
    • Remove the 17 mm upper control arm castle nut
    • Hit the upper knuckle to release the ball joint stud
    • Remove the 10 mm nut securing the ABS wire bracket to the upper control arm
    • Move the knuckle forward to remove the strut
  3. step : Installing the Strut (5:25)
    • Insert the strut top mounting studs into position
    • Install the three 14 mm top mount nuts and the two 12 mm nuts
    • Torque the three 14 mm nuts to 37 ft-lb
    • Torque the two 12 mm nuts to 16 ft-lb
    • Insert the lower strut into the wishbone
    • Install the 14 mm lower strut bolt
    • Torque the 14 mm lower strut bolt to 32 ft-lb
    • Align the wishbone with the lower control arm
    • Install the 17 mm bolt and tighten the 17 mm nut onto it
    • Torque the 17 mm wishbone bolt to 47 ft-lb
    • Insert the upper control arm ball joint into the knuckle
    • Install the ball joint castle nut
    • Torque the ball joint castle nut to 35 ft-lb
    • Continue tightening to align the castle nut with the cotter pin hole in the stud
    • Install the new cotter pin
    • Install the ABS wire bracket onto the upper control arm
    • Install the 10mm nut securing the bracket
  4. step : Installing the Wheel (11:53)
    • Slide the wheel onto the lug nuts
    • Replace the lug nuts and tighten them in a star pattern
    • Lower the vehicle with the wheel lightly touching the ground
    • Torque the lug nuts in a star pattern to 80 ft-lbs
    • Lower the vehicle completely

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 12mm Socket
  • 14mm Socket
  • 19mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 17mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2003-2007Honda Accord Honda Accord Front Driver Side Strut & Spring Assembly
Part 1ASTS00657
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: SCA57506