Replaces

2002-06 Nissan Altima Wheel Bearing & Hub Assembly TRQ BHA54237 - 1ASHR00105

This replacement hub and bearing assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Fits either the LH (Driver Side) or RH (Passenger Side) REAR
  • Replaces dealer part number: 43202-3Z000, 432023Z000
  • Direct replacement
  • Built to strict quality control standards
  • Fits models without ABS (Anti-Lock Brakes)

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:17)
    • Loosen the lug nuts with a 21mm socket and breaker bar
    • Raise and support the vehicle
    • Remove the lug nuts by hand
    • Pull the wheel off the studs
  2. step : Removing the Brake Pads (0:46)
    • Compress the brake caliper by hand
    • Loosen the two slide bolts from the caliper with a wrench and a dead blow hammer
    • Remove the top slide bolt
    • Swing the caliper around and off the brake pads
    • Tighten the lower slide bolt by hand
    • Remove the brake pads from the caliper bracket with a flat blade screwdriver
    • Remove the two 19mm bolts from the caliper bracket with a wrench and a dead blow hammer
    • Pull the caliper bracket off the wheel knuckle
    • Remove the slide pin from the caliper
    • Hang the caliper aside with a bungee cord
  3. step : Removing the Brake Rotor (4:33)
    • Make sure the emergency brake is off
    • Apply rust penetrant to the brake rotor
    • Strike the rotor with a dead blow hammer
    • If the brake rotor is still stuck, pull the rubber cap out of the brake rotor
    • Turn the emergency brake adjust with a flat blade screwdriver
    • Pull the brake rotor off the hub
  4. step : Removing the Hub (5:42)
    • Remove the four 17mm bolts from behind the wheel bearing
    • Pull the hub out
    • Tap the hub out with a rubber mallet if needed
  5. step : Installing the Hub (9:32)
    • Clean off the mating surface with rust penetrant and a wire brush
    • Insert the hub into place
    • Gently tap the hub into place with a rubber mallet
    • Torque the bolts between 58-68 foot-pounds
  6. step : Installing the Brake Rotor (6:13)
    • Slide the rotor backwards onto the hub
    • Spray the rotor with brake parts cleaner and a rag
    • Turn the emergency brake adjuster with a flat blade screwdriver to pull the e -brake shoes in
    • Clean the e-brake shoes with brake parts cleaner
    • Slide the rotor onto the hub
    • Fasten one lug nut onto a stud to hold the rotor in place
  7. step : Installing the Brake Pads (11:28)
    • Pry the brake pad clips out of the caliper bracket with a flat blade screwdriver
    • Clean the caliper bracket with brake parts cleaner and a wire brush
    • Clean the brake pad clips with brake parts cleaner and a wire brush
    • Pull the bungee cord off the brake caliper
    • Put an old brake pad in the caliper
    • Compress the caliper piston with the old brake pad and a C-clamp
    • Line up the caliper with the caliper bracket
    • Insert the lower slide pin into the caliper and the caliper bracket
    • Line up the caliper bracket on the wheel
    • Start the 19mm bolts for the caliper bracket
    • Clean the brake rotor with brake parts cleaner and a rag
    • Clean the brake pads with brake parts cleaner
    • Apply caliper grease to the brake pad ears
    • Place the brake pads into the caliper bracket
    • Swing the caliper onto the caliper bracket
    • Insert the top slide bolt into the caliper
    • Push the rubber cap into the brake rotor
    • Torque the two 19mm bolts to 120 foot-pounds
    • Torque the slide bolts to 30 foot-pounds
  8. step : Installing the Wheel (19:10)
    • Slide the wheel onto the studs
    • Start the lug nuts by hand
    • Lower the vehicle to the ground
    • Torque the lug nuts to 80 foot-pounds
    • Pump the brake pedal until the brakes feel firm

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack
  • Center Punch
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Bungee Cord
  • Anti-Seize Grease
  • Rust Penetrant
  • Brake Parts Cleaner
  • Paper Towels

  • Ratchets & Related

  • Socket Extensions
  • Ratchet
  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 17mm Socket
  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Dead Blow Hammer

  • Wrenches - Metric

  • 14mm Wrench
  • 17mm Wrench
  • 19mm Wrench
  • 21mm wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(19:49 min)

Tools List:

    General Tools

  • Jack Stands
  • Floor Jack
  • Center Punch
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Bungee Cord
  • Anti-Seize Grease
  • Rust Penetrant
  • Brake Parts Cleaner
  • Paper Towels

  • Ratchets & Related

  • Socket Extensions
  • Ratchet
  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 17mm Socket
  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Dead Blow Hammer

  • Wrenches - Metric

  • 14mm Wrench
  • 17mm Wrench
  • 19mm Wrench
  • 21mm wrench



This part replaces:

  • OE # 432023Z000
  • Hollander 538-58907
  • TRQ BHA54237

Vehicle Fit

  • 2002-2006 Nissan Altima Rear Wheel Bearing & Hub Assembly without ABS Brakes TRQ
Part #: 1ASHR00105

Ships Same Day for orders placed by 4 P.M. ET

TRQ
Brand #: BHA54237

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More