2002-06 Nissan Altima Wheel Bearing & Hub Assembly TRQ BHA53527 - 1ASHS00396

Frequently bought together

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
      Direct Fit Replacement
      Precision Engineered
      Highest Quality Materials
  • Bearing Type:   Ball Bearing

These replacement hub and bearing assemblies are just what you need to get your vehicle in good working order again.


  • Comes as a PAIR
    • Includes both the LH (Driver Side) & RH (Passenger Side) REAR
  • Replaces dealer part number: 43202-3Z000, 432023Z000
  • Direct replacements
  • Built to strict quality control standards
  • Fit models without ABS (Anti-Lock Brakes)

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm -

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:17)
    • Loosen the lug nuts with a 21mm socket and breaker bar
    • Raise and support the vehicle
    • Remove the lug nuts by hand
    • Pull the wheel off the studs
  2. step : Removing the Brake Pads (0:46)
    • Compress the brake caliper by hand
    • Loosen the two slide bolts from the caliper with a wrench and a dead blow hammer
    • Remove the top slide bolt
    • Swing the caliper around and off the brake pads
    • Tighten the lower slide bolt by hand
    • Remove the brake pads from the caliper bracket with a flat blade screwdriver
    • Remove the two 19mm bolts from the caliper bracket with a wrench and a dead blow hammer
    • Pull the caliper bracket off the wheel knuckle
    • Remove the slide pin from the caliper
    • Hang the caliper aside with a bungee cord
  3. step : Removing the Brake Rotor (4:33)
    • Make sure the emergency brake is off
    • Apply rust penetrant to the brake rotor
    • Strike the rotor with a dead blow hammer
    • If the brake rotor is still stuck, pull the rubber cap out of the brake rotor
    • Turn the emergency brake adjust with a flat blade screwdriver
    • Pull the brake rotor off the hub
  4. step : Removing the Hub (5:42)
    • Remove the four 17mm bolts from behind the wheel bearing
    • Pull the hub out
    • Tap the hub out with a rubber mallet if needed
  5. step : Installing the Hub (9:32)
    • Clean off the mating surface with rust penetrant and a wire brush
    • Insert the hub into place
    • Gently tap the hub into place with a rubber mallet
    • Torque the bolts between 58-68 foot-pounds
  6. step : Installing the Brake Rotor (6:13)
    • Slide the rotor backwards onto the hub
    • Spray the rotor with brake parts cleaner and a rag
    • Turn the emergency brake adjuster with a flat blade screwdriver to pull the e -brake shoes in
    • Clean the e-brake shoes with brake parts cleaner
    • Slide the rotor onto the hub
    • Fasten one lug nut onto a stud to hold the rotor in place
  7. step : Installing the Brake Pads (11:28)
    • Pry the brake pad clips out of the caliper bracket with a flat blade screwdriver
    • Clean the caliper bracket with brake parts cleaner and a wire brush
    • Clean the brake pad clips with brake parts cleaner and a wire brush
    • Pull the bungee cord off the brake caliper
    • Put an old brake pad in the caliper
    • Compress the caliper piston with the old brake pad and a C-clamp
    • Line up the caliper with the caliper bracket
    • Insert the lower slide pin into the caliper and the caliper bracket
    • Line up the caliper bracket on the wheel
    • Start the 19mm bolts for the caliper bracket
    • Clean the brake rotor with brake parts cleaner and a rag
    • Clean the brake pads with brake parts cleaner
    • Apply caliper grease to the brake pad ears
    • Place the brake pads into the caliper bracket
    • Swing the caliper onto the caliper bracket
    • Insert the top slide bolt into the caliper
    • Push the rubber cap into the brake rotor
    • Torque the two 19mm bolts to 120 foot-pounds
    • Torque the slide bolts to 30 foot-pounds
  8. step : Installing the Wheel (19:10)
    • Slide the wheel onto the studs
    • Start the lug nuts by hand
    • Lower the vehicle to the ground
    • Torque the lug nuts to 80 foot-pounds
    • Pump the brake pedal until the brakes feel firm

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack
  • Center Punch
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Bungee Cord
  • Anti-Seize Grease
  • Rust Penetrant
  • Brake Parts Cleaner
  • Paper Towels

  • Ratchets & Related

  • Socket Extensions
  • Ratchet
  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 17mm Socket
  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Dead Blow Hammer

  • Wrenches - Metric

  • 14mm Wrench
  • 17mm Wrench
  • 19mm Wrench
  • 21mm wrench

5.00/ 5.0
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Recommended Replacement to OEM
The fit was good as was the quality. Easy to install. We will see how long they last.
July 11, 2017
It was the right part and it worked perfectly. The instructional video made it very easy to take the old one off and put the new one on. IM A VERY PLEASED COSTOMER
June 4, 2018
Fixed my problem
Easy installation, reasonable price, would buy again
December 15, 2018
Perfect fit. Very happy with the quality and shipping!!
February 26, 2019
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2002-2006Nissan Altima Nissan Altima Rear Wheel Bearing & Hub Assembly Pair without ABS Brakes TRQ
Part #: 1ASHS00396

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Brand #: BHA53527

How-to Video:

(19:49 min)