2002-06 Nissan Altima Exterior Door Handle Front Passenger Side - 1ADHE00414

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Side Location:   Passenger Side
  • Color:   Black
  • Front or Rear Location:   Front
  • Finish:   Smooth - Paint to Match

This exterior door handle is just what you need to get your vehicle in good working order again!


  • Fits RH (Passenger Side) FRONT OUTER
  • Smooth Black Finish
    • Can be painted by buyer to any color desired or installed as is
  • Replaces dealer part number: 80606-8J009, 806068J009
  • Durable construction
  • Direct replacement for original handle
  • Without key cylinder hole

This door handle is a great replacement and has good cost savings over a dealer unit.

Paint To Match Note:

"Paint to match finish" refers to a smooth, paintable surface. This item will be shipped unpainted but will be ready for paint. Final preparation is suggested for better paint coverage and adhesion. 

This part can also be installed without painting if desired. 

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (0:38)
    • Pry off the screw cap inside the door pull with a flat blade screwdriver
    • Remove the Phillips head screw inside the door pull
    • Pry off the window switch panel with a flat blade screwdriver
    • Disconnect the wiring harnesses from the switch panel
    • Pry off the window base trim panel with a flat blade screwdriver
    • Pry off the screw cap inside the door handle with a flat blade screwdriver
    • Remove the Phillips screw inside the door handle
    • Remove the Phillips screw behind the door pull
    • Pull off the courtesy light
    • Disconnect the courtesy light from its wiring harness
    • Pry the door panel off by hand
    • Lift the door panel up and off
    • Disconnect the cables from the inner door handle
    • Disconnect the wiring harness from the door panel
  2. step : Removing the Regulator Panel (2:17)
    • Pull the wiring harnesses out of their clips
    • Peel off the two rubber covers with a razor blade
    • Connect the switch panel to its wiring harness
    • Turn the ignition on
    • Raise the window with the switch
    • Remove the two 10mm bolts from the window regulator
    • Pull the window out by hand
    • Disconnect the window switch from the inner door panel
    • Remove the nine 10mm bolts from the door panel
    • Pull off the regulator panel
  3. step : Removing the Outer Door Handle (4:22)
    • Undo the clips for the outer door handle rods
    • Pull the rods out of the outer door handle
    • Remove the small plastic cover from the door by hand
    • Remove the two 10mm bolts from the door handle
    • Pull the door lock wiring harness out of its clip
    • Push the outer door handle out of the door
    • Remove the 10mm bolt that holds the lock to the outer door handle
  4. step : Installing the New Outer Door Handle (5:47)
    • Paint the new door handle to the desired color
    • Attach the lock to the new outer door handle
    • Insert the 10mm bolt into the door lock
    • Feed the door handle into the door
    • Clip the rods onto the door handle
    • Insert the two 10mm bolts into the new outer door handle
  5. step : Reinstalling the Regulator Panel (6:56)
    • Put the regulator panel into place
    • Insert the nine 10mm bolts into the regulator panel
    • Slide the window into the door by hand
    • Replace the small plastic cover
    • Insert the two 10mm bolts into the window regulator
    • Put on the two rubber covers
    • Reconnect the wiring harnesses and push them into their clips
  6. step : Reinstalling the Door Panel (8:26)
    • Put the door panel into place
    • Connect the wiring harness to the door panel
    • Clip the two cables to the inner door handle
    • Pull the wiring harnesses through the door panel cavity
    • Put the door panel into place
    • Push in the door panel clips
    • Connect the courtesy light to the wiring harness
    • Push the courtesy light in to place
    • Insert the Phillips screw inside the door handle
    • Push in the screw cap inside the door handle
    • Insert the Phillips screw behind the door pull
    • Connect the wiring harnesses to the window switch panel
    • Insert the Phillips head screw into the door pull
    • Push in the screw cap inside the door pull
    • Push on the mirror base trim

Tools needed for replacement:

    General Tools

  • Razor Blade / Gasket Scraper

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

4.50/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Door handle for 2004 Nissan
I ask for an interior door handle you sent an exterior handle but you never told me that the interior handle was out of stock.I was waiting for the parts but only found out what happened when I called to see why it was taking so long.I like 1aauto and plan to use it in that future.
August 10, 2017
1st door handle
fit great, after painting, matched exact and worked better than rear handle
September 21, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2002-2006Nissan Altima Nissan Altima Smooth - Paint to Match Black Exterior Door Handle without Lock Provision Front Passenger Side
Part #: 1ADHE00414

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(10:18 min)