Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 4 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Rear Hub Assemblies
  • Kit Includes: (2) Rear Shock & Spring Assemblies
  • Quantity: 4 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:40)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Disconnecting the Strut (1:06)
    • Apply rust penetrant to the strut mount nuts
    • Pry out the inner fender clips with a flat blade screwdriver
    • Pull off the inner fender
    • Remove the three 13mm nuts from the strut mount
    • Remove the 21mm bolt from the bottom of the strut
  3. step : Removing the Sway Bar Link (3:35)
    • Apply rust penetrant to the sway bar link
    • Turn the sway bar link with a 16mm socket and ratchet
    • Remove the 15mm nut from the top of the sway bar link
    • Hold the sway bar link sleeve with vise grip pliers
    • Loosen the sway bar link from the bottom with a 16mm socket and ratchet
    • Push out the sway bar link with a hammer and punch
  4. step : Removing the Strut (5:29)
    • Apply rust penetrant to the lower strut nut
    • Hold the strut bolt with an 18mm wrench
    • Remove the 21mm nut from the wheel knuckle
    • Loosen the two 21mm nuts that hold the control arm to the frame
    • Lift the wheel knuckle up
    • Pull the strut down and out
  5. step : Installing the Strut (6:41)
    • Lift the strut into place
    • Start the three 13mm nuts onto the strut mount
    • Turn the bottom of the strut to line up the bolt hole with the control arm
    • Push the 21mm bolt into the bottom of the strut
    • Push the 18mm bolt into the wheel knuckle
    • Fasten the nut onto the strut bolt
    • Tighten the strut bolt and nut
    • Fasten the nut onto the wheel knuckle bolt
    • Tighten the wheel knuckle bolt and nut
    • Tighten the three 13mm nuts on the strut mount to 20-25 foot-pounds of torque
  6. step : Installing the Sway Bar Link (8:44)
    • Put a washer on the sway bar link
    • Put a bushing on the sway bar link
    • Slide the sway bar link through the control arm
    • Put a bushing on the sway bar link
    • Put a washer on the sway bar link
    • Put the sleeve onto the sway bar link
    • Put a washer on the sway bar link
    • Put a bushing on the sway bar link
    • Slide the sway bar link through the sway bar
    • Put a bushing on the sway bar link
    • Put a washer on the sway bar link
    • Fasten the 15mm nut onto the sway bar link
  7. step : Tightening the Suspension Parts (9:30)
    • Support the suspension at ride height with a jack
    • Tighten the sway bar link nut to compress the bushings
    • Tighten the two bolts that hold the control arm to the frame to 110 foot-pounds
    • Tighten the wheel knuckle bolt to 110 foot-pounds
    • Put the inner fender into place
    • Push the plastic clips into the inner fender
  8. step : Reattaching the Wheel (10:39)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Wire Cutters

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 13mm Socket
  • 15mm Socket
  • 16mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 16mm Wrench
  • 18mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
great quality great prices
Got my suspension kit quickly and at a great price. no auto parts store could beat 1a auto prices.
June 27, 2018
Purchased
2 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2002-2005Ford Explorer Ford Explorer 4 Door 4 Piece Set Steering & Suspension Kit
2002-2005Mercury Mountaineer Mercury Mountaineer 4 Piece Set Steering & Suspension Kit

This part replaces:

  • Hollander 538-01584
  • OE # 3L2Z1109AA, 6L2Z1109B
  • Hollander 538-01754
  • Monroe 181322
  • Monroe 171322
  • KYB SR4051
  • Hollander 538-01584, 538-01754
  • OE # 3L2Z 1109 AA, 6L2Z 1109 B
Part #: 1ASFK02751


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(11:37 min)