Replaces

2002-05 Honda Civic Steering & Suspension Kit - 1ASFK04857

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 6 Piece Set
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Quantity: 6 Piece Set
  • Kit Includes: (2) Front Strut & Spring Assemblies

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

    We recommend an alignment after completing this repair

  1. step : Removing the Wheel (0:50)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:21)
    • Loosen the 24mm lock nut with a 21mm wrench and hammer
    • Make note of how far you turn the inner tie rod to turn it back for reinstallation
    • Remove the 24mm nut from the outer tie rod end
    • Remove the cotter pin with needle nose pliers
    • Remove the ball joint nut
    • Strike the steering knuckle with a hammer to loosen the outer tie rod
    • Twist off the outer tie rod by hand
  3. step : Removing the Caliper (3:29)
    • Remove the 12mm bolt from the brake hose
    • Remove the 10mm bolt from the sensor wire
    • Remove the 12mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Secure the caliper up in place with wire ties
  4. step : Removing the Strut and Spring Assembly (4:29)
    • Remove the 21mm pinch nuts and 19mm bolts
    • Remove the three 13mm nuts from the top of the shock
    • Pull the strut out of the wheel knuckle
    • Pull the strut down and out
  5. step : Installing the Strut and Spring Assembly (5:55)
    • Place the studs that are a further distance apart to the outside of the vehicle
    • Insert the strut up into place
    • Hand tighten the 13mm nuts to the strut
    • Insert the wheel knuckle into the strut
    • Insert the 21mm pinch nuts and 19mm bolts into place
    • Torque the pinch bolts to 76 foot-pounds for 2001-2002
    • Torque the pinch bolts to 116 foot-pounds for 2003-2005
    • Tighten the 13mm nuts to 33 foot-pounds
  6. step : Reinstalling the Caliper (7:50)
    • Lower the caliper into place
    • Thread 12mm bolts by hand
    • Tighten bolts to 34 Newton Meters or 25 foot-pounds
    • Tighten the 10mm bolt to the sensor wire
    • Tighten the 12mm bolt to the brake hose
  7. step : Reinstalling the Outer Tie Rod (9:19)
    • Twist the new outer tie rod onto the inner tie rod
    • Push the outer tie rod into the steering knuckle
    • Fasten the castle nut onto the outer tie rod
    • Tighten the castle nut to 32 foot-pounds
    • Push the cotter pin through the castle nut
    • Twist the cotter pin into place with needle nose pliers
    • Make sure the inner tie rod is in its correct position
    • Hold the tie rod with an 18mm wrench
    • Tighten the 24mm lock nut
  8. step : Reattaching the Wheel (10:45)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 12mm Socket
  • 13mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 24mm Wrench
  • 21mm wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2002-2005Honda Civic Honda Civic (excluding Hybrid Models) 6 Piece Set Steering & Suspension Kit

This part replaces:

  • OE # 51320S5A003
  • OE # 51320SCVA91
  • OE # 51321S5A003
  • OE # 51321SCVA91
  • OE # 53541S5A003
  • Monroe 172186
  • Monroe 172185
  • KYB SR4129
  • KYB SR4128
  • Moog ES3581
  • Moog K90454
  • Moog K90455
  • OE # 51321-S5A-003
  • OE # 51320-S5A-003
Part #: 1ASFK04857

Out of Stock

How-to Video:

(11:26 min)