This replacement Tail light pair is just what you need to get your Honda CR-V in good looking form again!

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side)
  • DOT (Department of Transportation) & SAE (Society of Automotive Engineers) approved
  • Direct replacement
  • Built to strict quality control standards
  • Fits vehicles that were built in the U.K. (United Kingdom) only

Note: The first digit of your vehicle identification number (VIN) determines where it was built:

  • J = Japan
  • S = U.K.

The (VIN) number can be found on your vehicle registration or under the windshield near the driver's side front "A" pillar post.

We have noticed that there are many inferior quality Tail lights on the market. We have researched other tail light manufacturers and are only selling what we believe to be the highest quality, best fitting, aftermarket tail lights available. So don't be fooled by cheaper made imitation tail lights. Go with superior quality!

This Honda CR-V taillamp pair makes a great replacement and has good cost savings over a dealer Tail light.

Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Light uses same wiring as the original assembly, providing easy, trouble-free installation.  No cutting or splicing required.

DOT and SAE Compliant

DOT & SAE compliant: meets federal regulations for on-road use

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Taillight Assembly (0:43)
    • Pry out the two plugs to uncover the bolts.
    • Remove the 8mm bolts.
    • Pull the taillight out.
  2. step : Replacing a Bulb (1:49)
    • Twist the sockets out counterclockwise.
    • Pull the bulb straight out.
    • Push a new bulb in.
    • Twist the socket back in.
  3. step : Removing the Taillight Assembly Continued (2:22)
    • Remove the Panel, table, spare tire and the panel below the spare tire.
    • Remove the clips on the panel near the bumper. Remove the Panel.
    • Remove the Phillips screw by the taillight.
    • Remove the jack cover. Remove the jack.
    • Pry out the inner panel.
    • Disconnect the taillight harness.
    • Pull the grommet out and pull the light off.
  4. step : Replacing the Taillight Assembly (4:49)
    • Push in the harness.
    • Push the rubber grommet in.
    • Line-up and push the light into place.
    • Reconnect the harness.
    • Replace the inner panel.
    • Replace the Phillips screw.
    • Replace the jack and the jack cover.
    • Replace the lower panel.
    • Replace the Spare tire, panels and table.
    • Replace the two 8mm bolts.
    • Replace the two plugs.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2002-2004 Honda CR-V (UK Built Models (1st VIN Digit S)) Tail Light Pair

This part replaces:

  • OE # 33501SCAA00
  • OE # 33551SCAA00
  • Partslink HO2819127, HO2818127
Only 1 left in stock
Part #: 1ALTP00189



How-to Video:

(08:34 min)