Part Details

  • Quantity: 4 Piece Set
  • Kit Includes: (2) Front Upper Control Arms with Ball Joints
  • Front or Rear Location: Front & Rear

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Detaching the Strut (0:43)
    • Open the trunk
    • Pull back the trunk insulation
    • Pull off the strut cover
    • Remove the two 15mm nuts from the top of the strut
    • Raise and secure the vehicle
    • Apply penetrating oil to the lower strut bolt and nut
    • Remove the 18mm nut from the strut
    • Tap the strut bolt through with a hammer and pick
    • Remove the two plastic clips from the top of the strut
  2. step : Removing the Wheel (2:10)
    • Lower the vehicle to the ground
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. step : Removing the Strut (2:30)
    • Pry off the strut with a pry bar
    • Pull the strut down and out over the wheel
  4. step : Installing the New Strut (2:44)
    • Put the new strut into place over the wheel
    • Pull down the wheel as you push the strut into place
    • Position the strut with a pry bar
    • Hammer the bolt into the strut
    • Fasten the 18mm nut onto the strut bolt
    • Tighten the nut to between 75 - 80 foot-pounds
    • Insert the plastic clips into the top of the strut
  5. step : Reattaching the Wheel (4:01)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
  6. step : Reattaching the Strut (4:09)
    • Fasten the two 15mm nuts onto the top of the strut
    • Tighten the 15mm nuts to between 40 - 45 foot-pounds
    • Replace the strut cover
    • Put the trunk insulation back into place
  7. step : Fastening the Wheel (4:37)
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Pick

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 18mm Wrench

5.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
0
0
0
Rides like new
I replaced this is pension system in my girl's car, a 2001 Dodge Stratus SE sedan. She couldn't stop raving about how amazing the ride was in the difference after the install. So..good so far. Good quality parts it seems!
October 9, 2018
Purchased
3 weeks ago
Good price and good quality product.
My mechanic was impress with the superb quality of the strut kit assembly.
August 28, 2017
Purchased
1 year ago
Can't be this simple
If something is too good to be true, most likely it is....but 1A Auto is the exception to the rule. I was pleased from my online order, until my work was complete. They promptly shipped my parts and had a video to show me how to install them step by step. I recommend if you are playing any car repair definitely give them a chance. Your wallet and peace of mind will thank you....
March 26, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
Does this set come with the control arms already mounted to the struts?
Tony R on Sep 22, 2016
BEST ANSWER: Yes the fronts have the CA already installed

Vehicle Fit

Year Make Model Description
2001-2006Chrysler Sebring Chrysler Sebring Sedan Front & Rear Strut & Spring Assembly 4 Piece Set
2001-2006Dodge Stratus Dodge Stratus Sedan Front & Rear Strut & Spring Assembly 4 Piece Set

This part replaces:

  • Hollander 527-01467R
  • Hollander 527-01468L
  • Hollander 527-01469R
  • Hollander 527-01470L
  • Hollander 527-02027R
  • Hollander 527-02028L
  • Hollander 527-01472
  • Monroe 281311
  • Monroe 271311
  • KYB SR4107
Part #: 1ASSP01247


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(05:01 min)