In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Pre-assembled, loaded strut & spring assemblies allow for a quicker, safer install than replacing with just bare struts. 

Trouble-Free Install

Trouble-free install includes the matched parts needed to get the job done. New mounts, bearings, springs and hardware will provide a better ride for your vehicle and save you time from not having to do the job again because a used part failed afterwards.

Matched Parts

When you buy the kit pre-built by us, you can be sure that the parts are matched for optimum performance.  Not all shocks and struts are manufactured the same, so mixing and matching can result in fit issues and potentially decrease the life of the parts.

Saves Time & Money

When you buy one of our kits, you not only save money over buying the parts individually, but you also save time having to search for all of the different parts that are correct for your vehicle (because we did it for you!)

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Detaching the Strut (0:43)
    • Open the trunk
    • Pull back the trunk insulation
    • Pull off the strut cover
    • Remove the two 15mm nuts from the top of the strut
    • Raise and secure the vehicle
    • Apply penetrating oil to the lower strut bolt and nut
    • Remove the 18mm nut from the strut
    • Tap the strut bolt through with a hammer and pick
    • Remove the two plastic clips from the top of the strut
  2. step : Removing the Wheel (2:10)
    • Lower the vehicle to the ground
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. step : Removing the Strut (2:30)
    • Pry off the strut with a pry bar
    • Pull the strut down and out over the wheel
  4. step : Installing the New Strut (2:44)
    • Put the new strut into place over the wheel
    • Pull down the wheel as you push the strut into place
    • Position the strut with a pry bar
    • Hammer the bolt into the strut
    • Fasten the 18mm nut onto the strut bolt
    • Tighten the nut to between 75 - 80 foot-pounds
    • Insert the plastic clips into the top of the strut
  5. step : Reattaching the Wheel (4:01)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
  6. step : Reattaching the Strut (4:09)
    • Fasten the two 15mm nuts onto the top of the strut
    • Tighten the 15mm nuts to between 40 - 45 foot-pounds
    • Replace the strut cover
    • Put the trunk insulation back into place
  7. step : Fastening the Wheel (4:37)
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Pick

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 18mm Wrench

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
0
0
0
0
Easy
Great fit at a great price. Easy to install by with good instructions.
April 15, 2017
Purchased
1 year ago
Rear strut assembly
Parts were just what I ordered, fit perfectly with no problem whatsoever. Video for installation was right on point. Am now ordering front strut and shock assembly for vehicle. Would highly recommend. Only thing, I would like to see front strut assembly video which is not available.
February 3, 2018
Purchased
3 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 4 questions Browse 4 questions and 10 answers
will this fit the dodge stratus coupe v6 3.0?
travis on Jun 22, 2016
BEST ANSWER: No. The coupe Stratus was not built on the same assembly line as the 4 door models. Most if not all parts are not interchangable.
This part specifies that it is for the Sedan model. Where is this part for the Convertible (2001 Sebring, 2.7Lv6)?
Cornelius T on Sep 14, 2015
BEST ANSWER: Hey sorry for the late reply here's the link, m.1aauto/2001-06-chrysler-sebring-strut-and-spring-assembly-rear-pair-monroe-471311/i/mnssp00132?f=527976&y=2004 , I accidentally bought the sedan ones and then realized I had gotten the wrong ones hahah (just add the https and forward slashes to the beginning and dot com after 1aauto)
Replacing strut n spring video?
Ginger B on Sep 27, 2017
BEST ANSWER: Yes there is a video that helps you out there replacing part comes all in one pre assembled but I would recommend buying a upper control arm sometimes the bolts are stripped and had to be cut but otherwise a great product and well recommended Patrick
Will these shocks fit a 2006 chrysler sebring convertible?
Brion on Sep 2, 2017
BEST ANSWER: These will only fit the sedan model.

Vehicle Fit

  • 2001-2006 Chrysler Sebring Sedan Rear Strut & Spring Assembly Pair
  • 2001-2006 Dodge Stratus Sedan Rear Strut & Spring Assembly Pair

This part replaces:

  • Monroe 281311
  • Monroe 271311
  • KYB SR4107
Part #: 1ASSP00435



How-to Video:

(05:01 min)