Replaces

2001-06 Chrysler Sebring Strut & Spring Assembly Pair - 1ASSP01002

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Pre-assembled, loaded strut & spring assemblies allow for a quicker, safer install than replacing with just bare struts. 

Trouble-Free Install

Trouble-free install includes the matched parts needed to get the job done. New mounts, bearings, springs and hardware will provide a better ride for your vehicle and save you time from not having to do the job again because a used part failed afterwards.

Matched Parts

When you buy the kit pre-built by us, you can be sure that the parts are matched for optimum performance.  Not all shocks and struts are manufactured the same, so mixing and matching can result in fit issues and potentially decrease the life of the parts.

Saves Time & Money

When you buy one of our kits, you not only save money over buying the parts individually, but you also save time having to search for all of the different parts that are correct for your vehicle (because we did it for you!)

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Detaching the Strut (0:43)
    • Open the trunk
    • Pull back the trunk insulation
    • Pull off the strut cover
    • Remove the two 15mm nuts from the top of the strut
    • Raise and secure the vehicle
    • Apply penetrating oil to the lower strut bolt and nut
    • Remove the 18mm nut from the strut
    • Tap the strut bolt through with a hammer and pick
    • Remove the two plastic clips from the top of the strut
  2. step : Removing the Wheel (2:10)
    • Lower the vehicle to the ground
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. step : Removing the Strut (2:30)
    • Pry off the strut with a pry bar
    • Pull the strut down and out over the wheel
  4. step : Installing the New Strut (2:44)
    • Put the new strut into place over the wheel
    • Pull down the wheel as you push the strut into place
    • Position the strut with a pry bar
    • Hammer the bolt into the strut
    • Fasten the 18mm nut onto the strut bolt
    • Tighten the nut to between 75 - 80 foot-pounds
    • Insert the plastic clips into the top of the strut
  5. step : Reattaching the Wheel (4:01)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
  6. step : Reattaching the Strut (4:09)
    • Fasten the two 15mm nuts onto the top of the strut
    • Tighten the 15mm nuts to between 40 - 45 foot-pounds
    • Replace the strut cover
    • Put the trunk insulation back into place
  7. step : Fastening the Wheel (4:37)
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Pick

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 18mm Wrench

5.0 / 5.0
4 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
4
0
0
0
0
Seems great
I have only had these on a short time so cannot attest to the long term quality. But they seem well built and matched the old ones perfectly, so thus far I am happy with them. I will likely order similar ones for my 2008 Town & Country van. Lots of quality for the price, and how can you beat free and fast shipping?
January 27, 2018
Purchased
5 months ago
Took the rattle out of the back of the car. Rides like a new one now. I would recommend doing business with 1aauto to anyone. Happy camper here.
October 8, 2017
Purchased
8 months ago
Strut & Spring Assembly
After watching the video from 1A Auto on how to replace rear strut/spring assembly, I ordered this product from !A Auto online and it was shipped free to me very quickly. After receiving these parts that fit my car perfectly, I was able to install them quickly and easily. Another quality product from 1A Auto parts!
July 26, 2017
Purchased
10 months ago
Installed on 2004 Sebring Convertible
After searching for where the struts mount over the wheel well and finding them in the well where the top is stored, everything went slick and easy. had both sided installed in around an hour. Car rides like new. Was half price of what local supply stores were asking.
February 21, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001-2006 Chrysler Sebring Convertible Rear Strut & Spring Assembly Pair

This part replaces:

  • Monroe 471311
Part #: 1ASSP01002


How-to Video:

(05:01 min)