Replaces

2001-05 Honda Civic Wheel Bearing & Hub Kit Pair Front - 1ASHS00319

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Bearing Type:   Ball Bearing
  • Quantity:   Pair
  • Front or Rear Location:   Front

This front wheel hub & bearing PAIR are new aftermarket replacement parts. They are just what you need to keep you vehicle in good running condition. They usually get pressed together and then this PAIR is installed into the front knuckles. So if your front wheels are making noises and it is determined that your front wheel bearings & hubs are bad, this is the set for you!

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver's) & RH (Passenger's Side) FRONT
  • Direct replacement
  • Replaces dealer part numbers: 44600-S5D-A00, 44600-S5A-J00, 44600S5DA00, 44600S5AJ00, 44300-S5A-008, 44300S5A008
  • Fits 4 Lug Wheel
  • Studs already installed
  • Built to strict quality control standards
  • Wheel bearing is included
    • buyer will need to have bearing pressed onto hub

 

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:55)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:25)
    • Remove the dust cap with a chisel and hammer
    • Insert a tapered punch into the punched slit between the retainer and nut
    • Tap the punch to separate the nut
    • Remove the 32mm nut axle nut with a pry bar and breaker bar
  3. step : Removing the Caliper (1:52)
    • Remove the 17mm bolts from the caliper bracket
    • Remove the caliper and caliper brackets assembly from the rotor
    • Hand the caliper with a wire tie or bungee
  4. step : Separating the Ball Joint (2:28)
    • Bend the cotter pin tab out with needle nose pliers
    • Pry the cotter pin out
    • Remove the 17mm castle nut on the bottom of the ball joint
    • Tap up with a hammer to release the ball joint
    • Use a pickle fork to separate the ball joint if needed
  5. step : Removing the Spindle (3:45)
    • Remove the 22mm bolts from the bottom of the strut
    • Unbolt the wheel speed sensor with a 10mm socket and ratchet
    • Remove the sensor with a pair of pliers
    • Tap the center of the CV axle
    • Pull the axle out of the spindle
  6. step : Removing the Backing Plate and Hub (5:04)
    • Insert the hub and rotor into the hydraulic press
    • Press the hub out of the bearing
    • Remove the three Phillips screws from the backing plate
    • Remove the backing plate
  7. step : Removing the Bearing (5:37)
    • Squeeze the snap ring with snap ring pliers
    • Pry the snap ring out with a flat blade screwdriver
    • Press the bearing out with a hydraulic press
  8. step : Installing the Bearing (6:15)
    • Press the bearing into the knuckle with a hydraulic press
    • Attach the snap ring to a pair of snap ring pliers
    • Press the snap ring into the bearing
  9. step : Installing the Backing Plate and Hub (6:28)
    • Insert the backing plate to the knuckle
    • Tighten the three Phillips screws to the backing plate
    • Place the old bearing on the back of the inner bearing for support
    • Place the spindle into the hydraulic press
    • Insert the hub into the spindle with the hydraulic press until it bottoms out
  10. step : Installing the Spindle (7:04)
    • Insert the lower ball joint into the control arm
    • Line up and press the CV Axle into the hub
    • Insert the 22mm bolts (head facing front of car) into the bottom of the strut
    • Torque the strut bolts to 116 foot-pounds with a 19mm wrench on the bolt side
  11. step : Installing the Hub Nut (8:34)
    • Insert the hub nut into place
    • Torque the 32mm hub nut to 134 foot-pounds with a pry bar to keep the hub still
    • Dent the outer ring on the axle nut into the keeper groove with a hammer and pick
    • Tighten the 10mm bolt to the wheel speed sensor
  12. step : Installing the Ball Joint (9:38)
    • Align the castle nut with the windows on the control arm
    • Torque the castle nut to 43-50 foot-pounds
    • Insert the cotter pin into nut
    • Bend the cotter pin underneath
  13. step : Reinstalling the Brake Caliper (10:33)
    • Insert the brake rotor into place
    • Tighten the Number 2 Phillips screw to the brake rotor
    • Spread the pads and insert the caliper into place
    • Tighten the 17mm caliper bolts
    • Torque the caliper bolts to 80 foot-pounds
  14. step : Reattaching the Wheel (11:45)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 17mm Socket
  • 22mm Socket
  • 10mm Socket

4.64/ 5.0
11 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
8
2
1
0
0
Perfect Fit & Part
This is an excellent value that was a perfect fit and solved the problem of the humming. Delievery was before the expected date. I highly recommend 1AAuto.com!
February 20, 2017
Honda Civic Front Hubs and Bearings
Great price, great fit, free shipping took longer than expected but was fine for the weight.
July 3, 2017
Great service
Quick easy service, right part, very helpful video for installation instructions.
September 14, 2017
Perfect fit and good quality ,thanks
Quality parts,perfect fit,price right ,fast shipping Thanks
October 4, 2017
Wheel bearings on my 2002 Honda Civic
My wheel bearings where really shot from wear & tear on my Honda Civic. It was apparent to change them over as they making a loud growl noise. I chose Local Shop here in my town and this mechanic couldn’t find affordable replacements. So I just searched out your Company and showed him the price. He was amazed and said I could order them myself and he would install them for me. The parts came quickly and was packaged very well. Parts came in great condition and Mechanic had no problem installing them. My Car now runs smooth and quite. Thank you for the Great Deal for my Wheels! David
November 5, 2017
Exactly what we need
We have old cars and y’all helping us keepem on the road safely. Thank you.
November 16, 2017
01 civic front wheel bearings
Very nice set with bearings, hubs and new axle nuts. A1auto online video instructions were great. Civic is very quiet when driving. Price was very good for the complete set. I will shop here again as parts are needed for the civic.
April 16, 2018
Great product!
I work on all cars makes and models. When looking for quality parts I do lots of research on durability and price. With 1a Auto I find you get great prices/ and parts. I will be buying a lot more from 1A Auto to back cars I work on!
September 21, 2018
Great Bearing and hub kit.
Old wheel bearings were making noise so loud at highway speeds it was hard to hear the radio. Changed out wheel bearings and hub kit and the noise went away. I can now listen to my favorite tunes again.
October 21, 2018
Great Products
These were a direct fit. Take off old ones out these new bad boys on. Perfection for this company is great. Awesome products for an even better price.
December 2, 2018
Good but bearings might be cheap..
The order was sent out right away but the shipping was more than 3 days late. The bearings seem kinfa cheap im getting a rumbling sound from the front driver side bearing. I dont know if it is just cheap and broke from the start or if it is not the right one. Im gonna drive on them alittle to see if the bearing still makes the sound dont want to take it all back apart to check it just feeling meh on the quality lets hope all turns out good. But great price.
December 4, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Does this kit come with new rings and nut?
David M April 7, 2018
No
Donnell P April 8, 2018
It did not come with nuts, and I used the ones that came with the car. I believe the kit did not come with rings,too. I will say the kit works in an excellent manner, and I did this work on 12/9/2016.
CARY B April 8, 2018
No, this kit just comes with bearings and hubs as pictured.
Tim K April 9, 2018
Kit came with hubs, bearings and nuts. Did not come with rings.
S C October 22, 2018
Which way does the bearing go into the knuckle?
Michael M July 21, 2018
Sometimes they are interchangeable. Otherwise, test to see which side is magnetic and that side should face out.
Peter M July 21, 2018
From the rear of the knuckle,,,
Timbolake C July 21, 2018
Year Make Model Description
2001-2005Honda Civic Honda Civic Front Wheel Bearing & Hub Kit (excluding SI Models) Pair
Part #: 1ASHS00319


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(12:29 min)