Replaces

2001-05 Honda Civic Wheel Bearing & Hub Assembly Rear Pair TRQ BHA54272 - 1ASHS00494

Part Details

  • Wheel Bearing & Hub Assembly Features & Benefits:
    Direct Fit Replacement
    Precision Engineered
    Highest Quality Materials
  • Bearing Type: Ball Bearing
  • Quantity: Pair
  • Front or Rear Location: Rear

These replacement wheel bearing & hub assemblies are just what you need to get your vehicle in good working order again.

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) REAR
  • Replaces dealer part number: 42200-S5A-008, 42200S5A008
  • Fit 4 Lug Wheels
  • New studs already installed
  • Direct replacements
  • Built to strict quality control standards
  • Fit models with Rear Drum Brakes only
  • Correct for models with ABS (Anti-Lock Brakes)

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

BHA54272 Axle / Spindle Nut Torque Specification

  1. step : Removing the Wheel (0:44)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Wheel Speed Sensor (1:10)
    • Remove the 10mm bolt behind the wheel speed sensor
    • Wiggle the speed sensor out
  3. step : Removing the Brake Shoes (1:49)
    • Strike the rotor/brake drum with a hammer if it will not come off
    • Remove the rotor/brake drum
    • Remove the two brake shoe springs with the vise grip pliers
    • Twist off the front retaining spring with the vise grip pliers
    • Hold the retaining pin in place by hand
    • Pry off the brake retainer with a flat blade screwdriver and turn it off the pin
    • Remove the brake shoe
    • Remove the retainer pin
    • Repeat the process for the other side, letting the rear shoe hang on the e-brake
    • Remove the adjustor
    • Rotate the e-brake shoe with vice-grips
    • Push the brake shoe off the e-brake
  4. step : Removing the Rear Bearing (4:00)
    • Remove the dust cap with a chisel and hammer
    • Insert a tapered punch into the punched slit between the retainer and nut
    • Tap the punch to separate the nut
    • Remove the 32mm nut axle nut
    • Tap the back of the wheel hub from the back of the spindle
    • If the inner race is stuck to the spindle, work it off with a chisel and hammer without scoring the spindle
  5. step : Installing the New Rear Bearing (5:44)
    • Inspect your spindle for scores, gouges, or any other damage
    • Slide the wheel bearing onto the hub
    • Tighten the 32mm axle nut
    • Torque the axle nut to 134 foot-pounds
    • Punch the outer ring of the axle nut into the keeper with a chisel and hammer
    • Tap the dust cap into place
    • Spin the wheel bearing and listen for grinding or crunching sounds
  6. step : Reinstalling the Brake Shoes (7:11)
    • Secure the end of your e-brake cable with vise grip pliers
    • Push the spring back with the hook on the e-brake spreader
    • Hook the lower brake spring into the shoe brake
    • Insert the retainer pin in the back
    • Insert the retainer clip over the pin
    • Press the retainer clip into place
    • Press the clip down and rotate the pin to keep it in place
    • Hook the spring into the remaining pad underneath the tab
    • Repeat the process for the other side
    • Spin the star wheel on the adjustor so it's clamped together
    • Insert the adjustor into place with the longest leg facing you
    • Insert the adjustor arm into place
    • Hook the retainer spring to the brake shoes
    • Adjust out your brake shoes by turning the star wheel up with a flat blade screwdriver
    • Replace the rotor/brake drum
  7. step : Reattaching the Wheel (10:36)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
  8. step : Installing the Wheel Speed Sensor (10:39)
    • Insert the wheel speed sensor into place
    • Tap it with an extension and dead blow hammer if necessary
    • Tighten the 10mm bolt to the sensor
  9. step : Reattaching the Wheel (11:10)
    • Lower the vehicle to the ground
    • Torque the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Rubber Mallet
  • Jack Stands
  • Chisel
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Needle nose pliers

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 10mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Very quick shipping and good quality parts. Excellent staff and willing to help with anything.
April 17, 2018
Purchased
5 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
How do I know which wheel bearing to use on my 2003 4wd honda civic?
Jerome G on Apr 23, 2018
BEST ANSWER: I called the 1-800 number and spoke with a representative. He asked for my VIN and matched up the appropriate wheel bearing for my vehicle. Try that and see if it works for you.

Vehicle Fit

Year Make Model Description
2001-2005Honda Civic Honda Civic Rear Wheel Bearing & Hub Assembly L4 1.7L Models with ABS Brakes & Rear Drum Brakes Pair TRQ

This part replaces:

  • TRQ BHA54272
Part #: 1ASHS00494


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA54272

How-to Video:

(11:37 min)