2001-05 Honda Civic Shock & Spring Assembly Pair - 1ASSP00130

Part Details

  • Quantity: Pair

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Accessing the Strut (0:40)
    • Remove the trunk carpet
    • Unscrew the plastic retainer from the trunk trim
    • Remove the two plastic clips from the trunk trim
    • Pull off the trunk trim
    • Remove the two 14mm nuts from the top of the strut
  2. step : Removing the Wheel (1:25)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the four 19mm lug nuts
    • Pull off the wheel
  3. step : Removing the Strut (1:35)
    • Remove the 17mm bolt from the bottom of the strut
    • Pull the strut out of the bracket with a pry bar
  4. step : Installing the Strut (2:38)
    • Lift the strut into place
    • Start the two 15mm nuts onto the top of the strut by hand
    • Pull the suspension down with a pry bar
    • Push the lower strut mount into place
    • Insert the 13mm bolt into the lower strut mount
    • Tighten the 13mm bolt
  5. step : Reattaching the Wheel (3:35)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
  6. step : Fastening the Strut (3:43)
    • Lower the vehicle enough to put weight on the suspension
    • Tighten the two 15mm nuts onto the top strut mount
    • Put the trunk trim into place
    • Push the two clips into the trunk trim
    • Screw the retainer into the trunk trim by hand
    • Put the trunk carpet into place
  7. step : Fastening the Wheel (4:37)
    • Tighten the four lug nuts to 80 foot-pounds in a crossing or star pattern
    • Lower the vehicle completely to the ground

Tools needed for replacement:

    Air Powered Tools

  • 3/8 Inch Air Impact Gun

  • General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Swivel
  • Ratchet
  • Torque Wrench
  • 3/8 Inch Drive Ratchet

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 17mm Socket
  • 14mm Socket
  • 15mm Socket

4.6 / 5.0
5 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Good deal
I called and ordered over the phone and item came within the next few days. I installed the item as per the video. Very satisfied with purchase and quality of material. Would recommend and buy from them again.
May 17, 2018
4 months ago
Ordering and receiving went great. Installation was more difficult than the video.
I needed a second set of hands to crowbar the rear end assembly down to install the shock bottom bolt. Make sure to have both wheels off the ground with jack stands not supporting the rear end assembly so that it will flex down. Honda dealer wanted $900 for the pair. Huge difference in price and only time will tell on the quality. The new shocks are now squeaking and I presume that will go away?
February 12, 2018
7 months ago
Civic Shock & Spring Assembly
Correct parts and they were easy to install with the help of the installation video. Car rides much smoother and quitter.
January 9, 2018
8 months ago
Got what I paid for
The struts fit great and the ride is smooth. I only commute 10 miles a day so these should keep my 02 civic riding well until it dies!
September 8, 2017
1 year ago
i can hear the radio
after installing the new shocks i can hear the radio and dont hear clunk clunk and great price too
July 27, 2017
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 4 answers
Who was the manufacturer of these rear shock struts (2001-2005 civic)? Anything else I should know?
Phil S on Aug 14, 2017
BEST ANSWER: I don't recall the actual name of the manufacturer but these are pretty prevalent as a cheap Chinese made replacement strut. They would compete with Sensen but probably aren't as good of quality as Sensen. They fit well on my 2003 Civic and have performed well since I installed them roughly 2 1/2 years ago. If you're on a budget or you don't think you'll have the car for more than another 40K or 50K miles then I think they're a reasonable option.

Vehicle Fit

Year Make Model Description
2001-2005Honda Civic Honda Civic Rear Shock & Spring Assembly Pair

This part replaces:

  • Monroe 171340L
  • Monroe 171340R
Part #: 1ASSP00130

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(05:09 min)