2001-05 Honda Civic Fuel Tank Filler Neck - 1AFMX00182

This replacement fuel filler neck is just what you need to get your vehicle in good working order again!


  • Fuel Tank Filler Neck
  • Replaces dealer part number: 17660-S5A-A31, 17660S5AA31
  • Direct fit replacement
  • Built to strict quality control standards
  • Replaces any gas tank filler neck that is rusted, rotted, bent, or damaged from an accident
  • Fits DX, EX, HX, or LX Models
    • Does NOT fit GX, SI, or Hybrid Models

This fuel filler neck is a great replacement and has good cost savings over a gas tank filler neck from the dealer.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

    Wheel removal is not shown in this video

  1. step : Removing the Wheel (0:48)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the hub cap
    • Pull off the wheel
  2. step : Removing the Filler Neck (0:48)
    • Remove the plastic pins from the wheel well with a Phillips head screwdriver
    • Pull off the inner fender
    • Loosen the fuel hose clamp with a 7mm socket and ratchet
    • Slide back the hose clamp
    • Slide back the clamps on the two smaller hoses
    • Apply rust pentrant to the filler neck bracket bolts
    • Remove the two 10mm bolts from the lower filler neck bracket
    • Remove the 10mm bolt from the filler neck bracket in the wheel well
    • Twist off the gas cap
    • Pull the filler neck down and out
  3. step : Installing the Filler Neck (3:41)
    • Lift the filler neck into place
    • Insert the 10mm bolt into the filler neck bracket in the wheel well
    • Insert the two 10mm bolts into the lower filler neck bracket
    • Push the hose onto the filler neck
    • Tighten the hose clamps
    • If any plastic clips remained in the filler neck, pry them out with a flat blade screwdriver
    • Put the inner fender into place
    • Insert the plastic clips into the inner fender
    • Twist on the gas cap
  4. step : Reattaching the Wheel (6:27)
    • Slide the wheel into place
    • Put the hub cap into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut to 100 foot-pounds

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 7mm Socket
  • 19mm Socket
  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001-2005 Honda Civic LX Fuel Tank Filler Neck
  • 2001-2005 Honda Civic DX Fuel Tank Filler Neck
  • 2001-2005 Honda Civic EX Fuel Tank Filler Neck
  • 2001-2005 Honda Civic HX Fuel Tank Filler Neck

This part replaces:

  • OE # 17660S5AA31
  • Dorman 577-825
Part #: 1AFMX00182

How-to Video:

(07:06 min)