2001-05 Honda Civic CV Axle Shaft TRQ CSA82383 - 1AACV00178

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit


  • Brand New CV Axle
  • Fits RH (Passenger Side) Front
  • Direct replacement
  • Built to strict quality control standards

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

Note: This is correct for models with or without ABS brakes.  The tone ring can be removed if the original CV axle did not have one and the vehicle did not originally come equipped with ABS brakes.

100% New Components

For quality fit, finish, and easy installation.

Heat Treated

For longer-lasting life and consistent performance under different road conditions.

Precision Machined

And made of brand new components, held to tighter tolerances for better consistency than rebuilt parts.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

    We recommend an alignment after completing this repair

  1. step : Removing the Wheel (0:50)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:27)
    • Remove the center cap from the wheel
    • Slide the wheel into place
    • Lower the vehicle to the ground
    • Have an assistant hold the brakes
    • Remove the 32mm nut with a large breaker bar
    • Secure the vehicle on jack stands
    • Pull off the wheel
    • Check to make sure the axle is free from the hub
  3. step : Removing the Caliper (2:03)
    • Remove the 12mm bolt from the brake hose
    • Remove the 10mm bolt from the sensor wire
    • Remove the 12mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Secure the caliper up in place with wire ties
  4. step : Removing the Axle (2:58)
    • Remove the 21mm pinch nuts and 19mm bolts
    • Pull the wheel knuckle out
    • Pry the axle out with a pry bar
    • Place a drain pan beneath the transmission
    • Pry the axle out of the transmission with a pry bar
  5. step : Installing the Axle (4:39)
    • Insert the axle into the transmission
    • Remove the new 32mm nut from the axle splines
    • Insert the axle into the wheel knuckle
    • Insert the 21mm pinch nuts and 19mm bolts into place
    • Hand tighten the 32mm hub nut
  6. step : Reinstalling the Caliper (6:10)
    • Place grease on your brake pads
    • Lower the caliper into place
    • Thread 12mm bolts by hand
    • Tighten bolts to 34 Newton Meters or 25 foot-pounds
    • Tighten the 10mm bolt to the sensor wire
    • Tighten the 12mm bolt to the brake hose
  7. After tightening, you might have to take the wheel off and dent the hub nut

  8. step : Reattaching the Wheel (7:39)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern
    • Tighten the hub nut to 134 foot-pounds or 181 Newton Meters
    • Replace the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Drain Pan
  • Assistant
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 32mm Socket
  • 21mm Socket
  • 19mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 19mm Wrench

5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
01 civic ex axle
Fit right (don’t forget to tap a little to seat it) got here on time.
July 7, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2001-2005Honda Civic Honda Civic CV Axle Shaft L4 1.7L Automatic Transmission Passenger Side (excluding SI Models) TRQ CSA82383
Part #: 1AACV00178

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Brand #: CSA82383

How-to Video:

(08:53 min)