Replaces

2001-05 Honda Civic Control Arm with Ball Joint - 1ASFK02294

Specifications:

  • Fits LH (Driver Side) Front Lower
  • Arm includes both bushings
  • Direct replacement
  • Built to strict quality control standards

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:51)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:22)
    • Insert a tapered punch into the punched slit between the retainer and nut
    • Tap the punch to separate the nut
    • Remove the 32mm nut axle nut with a pry bar and breaker bar
  3. step : Removing the Caliper (1:48)
    • Remove the 17mm bolts from the caliper bracket
    • Remove the caliper and caliper brackets assembly from the rotor
    • Hand the caliper with a wire tie or bungee
  4. step : Separating the Ball Joint (2:34)
    • Bend the cotter pin tab out with needle nose pliers
    • Pry the cotter pin out
    • Remove the 17mm castle nut on the bottom of the ball joint
    • Tap up with a hammer to release the ball joint
    • Use a pickle fork to separate the ball joint if needed
  5. step : Removing the Spindle (3:42)
    • Remove the 22mm bolts from the bottom of the strut
    • Unbolt the wheel speed sensor with a 10mm socket and ratchet
    • Remove the sensor with a pair of pliers
    • Tap the center of the CV axle
    • Pull the axle out of the spindle
  6. step : Removing the Ball Joint (4:56)
    • Insert the cup of the press over the cup of the ball joint
    • Press the jig onto the ball
    • Press the lower cup onto the jib
    • Install the press onto the tools
    • Using a 22mm socket with a breaker bar, tighten down on the press
    • Remove the ball joint
  7. step : Installing the Ball Joint (6:38)
    • Insert the ball joint into the spindle
    • Insert the larger cup onto the bottom of the ball joint
    • Insert the small cup onto the bottom of the larger cup
    • Install the press onto the top of the ball joint and the lower cups
    • Tighten the press until the ball joint bottoms out
    • Insert the snap ring onto the base of the ball joint with needle nose or snap ring pliers
    • Remove the 19mm castle nut from the ball joints
  8. step : Installing the Spindle (8:39)
    • Insert the lower ball joint into the control arm
    • Line up and press the CV Axle into the hub
    • Insert the 22mm bolts (head facing front of car) into the bottom of the strut
    • Torque the strut bolts to 116 foot-pounds with a 19mm wrench on the bolt side
  9. step : Installing the Hub Nut (8:34)
    • Insert the hub nut into place
    • Torque the 32mm hub nut to 134 foot-pounds with a breaker bar to keep the hub still
    • Dent the outer ring on the axle nut into the keeper groove with a hammer and pick
    • Tighten the 10mm bolt to the wheel speed sensor
  10. step : Installing the Hub Nut (9:57)
    • Insert the hub nut into place
    • Torque the 32mm hub nut to 134 foot-pounds with a breaker bar to keep the hub still
    • Dent the outer ring on the axle nut into the keeper groove with a hammer and pick
    • Tighten the 10mm bolt to the wheel speed sensor
  11. step : Installing the Ball Joint (11:00)
    • Align the castle nut with the windows on the control arm
    • Torque the castle nut to 43-50 foot-pounds
    • Insert the cotter pin into nut
    • Bend the cotter pin underneath
  12. step : Reinstalling the Brake Caliper (11:58)
    • Insert the brake rotor into place
    • Tighten the Number 2 Phillips screw to the brake rotor
    • Spread the pads and insert the caliper into place
    • Tighten the 17mm caliper bolts
    • Torque the caliper bolts to 80 foot-pounds
  13. step : Reattaching the Wheel (13:08)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Pick
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Snap Ring Pliers
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 17mm Socket
  • 10mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Pickle Fork

  • Wrenches - Metric

  • 19mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
The arm came packed appropriately with bushings already in place it made the job easy for the first time replacing one I will shop there again
October 26, 2017
Purchased
11 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2001-2005Honda Civic Honda Civic Sedan Front Lower Control Arm with Ball Joint Driver Side
2001-2005Honda Civic Honda Civic Coupe Front Lower Control Arm with Ball Joint Driver Side

This part replaces:

  • Dorman 520-925
  • Hollander 512-58745L
  • Moog K90332
  • Moog K640288
  • OE # 51220S5A003
  • OE # 51360-S5A-A20
Part #: 1ASFK02294


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(13:53 min)