2001-05 Honda Civic Acura EL Valve Cover Gasket Set FEL-PRO VS50606R - FPEGS00029

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit



  • Fel-Pro® Brand Valve Cover Gasket Set
  • Includes:
    • Valve Cover Gaskets
    • Spark Plug Tube Seals
  • Made from high quality materials
  • Direct replacements
  • Built to strict quality control standards
  • Fits models with L4 1.7L Engine only

Federal-Mogul's Fel-Pro® brand is our premium sealing system and the industry's leading brand of replacement sealing products for light vehicles, light trucks, medium-duty trucks and heavy-duty applications.

Item Condition: New

Wear and Tear

This item is backed by a 60-day warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. 

  1. step : Removing the Valve Cover (0:34)
    • Loosen the two plastic flat head screws from the engine cover
    • Remove the engine cover
    • Disconnect the ignition coil electrical connectors
    • Remove the three 10mm bolts holding the wiring harness to the valve cover
    • Pull the cable hold-down off the stud
    • Pry the wiring harness off of the valve cover with a flat blade screwdriver
    • Remove the four 10mm nuts from the ignition coils
    • Pull out the ignition coils
    • Remove the 10mm nuts from the throttle cable
    • Remove the oil dipstick
    • Twist off the oil cap
    • Disconnect the PVC breather hose
    • Loosen the five 10mm studs from the valve cover
    • Pry the wiring harness retainer from its studs with the flat blade screwdriver
    • Disconnect the A/C line hold-down with a flat blade screwdriver
    • Pull the power steering line off the valve cover bracket
    • Pull the A/C line off the valve cover bracket
    • Lift the valve cover up and off
  2. step : Removing the Valve Cover Gaskets (3:25)
    • Pull up the valve cover gasket with a pick
    • Peel off the valve cover gasket
    • Pull up the ignition coil gaskets with a pick
    • Peel off the ignition coil gaskets
    • Pry the studs off the top of the valve cover
    • Cut off the valve cover stud gaskets with wire cutters or a razor
    • Slide the washer off the stud
  3. step : Installing the Valve Cover Gaskets (5:50)
    • Slide the washers onto the valve cover stems
    • Slide on the valve cover stud gaskets
    • Put the studs into place on the valve cover
    • Install the valve cover gasket with the tabs on the timing cover side
    • Firmly press in the gasket
    • Push in the ignition coil gaskets with the bezel facing the engine side
    • Firmly press in the gaskets
  4. step : Installing the Valve Cover (7:08)
    • Clean the gasket sealing area with a solvent and a paper towel
    • Slide the valve cover onto the timing cover side, first
    • Maneuver the valve cover into place
    • Put the long bolts into the intake side of the engine
    • Put the shorter bolts into the exhaust side of the engine
    • Tighten the 10mm bolts to 7.2 foot pounds of torque
    • Put the wiring harness retainer into place
    • Connect the PVC breather hose
    • Push the power steering hose into the bracket
    • Push the A/C hose into the bracket
    • Push the ignition coils into place
    • Tighten the four 10mm nuts onto the ignition coil
    • Putt the wiring harness into place
    • Connect the ignition coil wiring harnesses
    • Insert the two 10mm bolts into the wiring harness
    • Push the cable retainer onto the stud
    • Fasten the two 10mm nuts onto the cable retainer
    • Tighten all the 10mm nuts and bolts
    • Twist on the oil cap
    • Put the oil dipstick into place
    • Put the engine cover into place
    • Tighten the two plastic flathead screws into the engine cover
    • Start the engine
    • Check for leaks

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Paper Towels

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

5.00/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
great quality to repair the subpar job someone else did in the psat
I purchased a used Honda Civic and noticed the valve cover was beginning to leak (even after the timing belt was replaced with new gaskets). I put these in and the leaks have gone away. Definitely take you take the time to seat this properly.
April 14, 2018
I like buying from u guys good quality & fast shipping so far no problems looking forwards for future purchase
January 18, 2019
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2001-2005Acura EL Acura EL Valve Cover Gasket Set
2001-2005Honda Civic Honda Civic L4 1.7L Valve Cover Gasket Set
Part #: FPEGS00029

Out of Stock

Brand #: VS50606R