2000-08 Ford Focus Brake Kit Nakamoto 80117, S747 - 1ABDS00019

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Kit Includes:
      (1) Rear Brake Shoe Set
      (2) Rear Brake Drums with Wheel Bearings

Rear Drum Specifications:

  • Comes as a Pair
    • Fits both LH (Driver Side) & RH (Passenger Side) Rear
  • Direct replacements
  • 4 wheel studs included per drum as shown
  • Drum Size: 8 x 1-15/32 Inches
  • Includes Bearings

Rear Brake Shoes Specifications:

  • Comes as a Pair
    • Fits both LH (Driver Side) & RH (Passenger Side) Rear
  • Premium Bonded Brake Shoes
  • Direct replacement
  • Correct for: 8 x 1-15/32 Inch Drums

Note: This set contains enough pieces to do both sides on one rear axle - (2) rear brake drums & (1) rear brake shoe set.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm -

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Brake Drum (0:52)
    • Remove the wheel by loosening the lug nuts (replace a lug nut and kick the wheel to break it loose if necessary)
    • Use a hammer and cold chisel on the dust cap. Dent the cap down and out. Turn and repeat until it comes free
    • Remove the 30mm socket using a ratchet and breaker bar
    • Pull the drum free
  2. step : Removing the Brake Shoes (1:43)
    • Using pliers lock on the springs and pull them free
    • Remove the two clips using a flat blade screwdriver
    • Pull the brake shoe free
    • Pull the other brake shoe free twisting until the metal ball comes free from the shoe
    • Remove the springs on the backside of the shoe by pulling the pieces apart
  3. step : Replacing the Brake Shoes (5:25)
    • Push the automatic adjuster on the crossbar removed from old brake into place on the new shoe. With a spring in between the parts
    • Use a wire brush to clean the pads the brake shoes fit onto
    • Make sure the cylinder is not leaking
    • Place grease in the divits on the new brake shoes. Attach the emergency brake cable back to the brake shoe
    • Push the pins (springs) back through into the brake shoes
    • Put the other brake shoe into place and insert the clips and springs
    • Slide cross bar back into place
    • Squeeze the shoes together. To help with inserting the blue springs
    • Center the brake shoes
  4. step : Replacing the Brake Drum and Wheels (10:56)
    • Line up the drum and slide it into place
    • Replace the 30mm nut. Torque it to 170 ft/lbs
    • While torqueing it spin the bearings
    • Replace the dust cap
    • Put the wheel into place and tighten the lug nuts to 100 ft/lbs
    • Pump the brakes until the pedal is firm

Tools needed for replacement:

    General Tools

  • Hammer
  • Chisel
  • Wire Brush
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 30mm Socket
  • 19mm Socket

5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Pleasantly surprised
It was a perfect fit as advertised. Came with dust shields in place way better than pressing the bearing out of the drum like I naively did before. It was simple but this was pull off swap the shoes slide on and done. Great quality.
October 25, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
M T November 16, 2015
Does this drum come with the ABS sensor ring?
Jason K September 16, 2016
It does not,just take ring off old drum and put on new.It will accept the ring,other drums will not.1A Auto drum does accept ring
John D September 17, 2016
I dont believe it came with the sensor ring, my Focus doesnt have ABS so it wasnt an issue for me.
Ryan E September 17, 2016
This does not come with the tone ring on this. You can reuse the ABS tone rings on these.
Derek C September 20, 2016
Take ring off old drum and put on new drum from 1A auto.It will accept the ring
John D September 22, 2016
Is the baring already pressed into the drum?
Bryson A November 16, 2018
Yes. You do not have to press in the bearing because its already in there. The toughest part for me doing the job was pulling off the old bearing, since on one side, the inner race was rusted onto the axle and stayed stuck onto it when I pulled the old bearing/drum assembly off. I had to cut the bearing race off by making a notch in it with a cutoff wheel and hammering it apart with a cold chisel.
Dietrik V November 16, 2018
Yes, the bearing is inside the drum already
W A November 16, 2018
Yes. All you have to do is pull your old drums off, replace the brakes, and slide the new drums on and youre good to go. Just make sure you set up the brake pads properly the first time because youre not gonna want to have to put those drums on twice.
Brandon G November 16, 2018
Yes. Ready to install.
Ray W November 16, 2018
yes it is
Curtis R November 16, 2018
Yes, the bearings will be pressed into the drums.
Jessica D November 16, 2018
Yes. Took about 30 min each side to replace shoes, clean and then slide on the new drum w/ bearing and tighten it all back up
M H November 16, 2018
Yes it is. These are good parts i put them on my focus and i haven’t had any problems
David F November 17, 2018
Year Make Model Description
2000-2008Ford Focus Ford Focus Rear Brake Kit Nakamoto
Part #: 1ABDS00019

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Brand #: 80117, S747

How-to Video:

(13:42 min)