Replaces

2000-08 Ford Focus Brake Kit Nakamoto 80090, S747 - 1ABDS00017

Rear Drum Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver) & RH (Passenger Side) REAR
  • Direct replacements
  • 4 wheel stud holes
  • Drum Size: 8 x 1-15/32 Inches

Rear Brake Shoes Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver) & RH (Passenger Side) REAR
  • Premium Bonded Brake Shoes
  • Direct replacement
  • Correct for: 8 x 1-15/32 Inch Drums

Note:
The drums do not include wheel bearings or seals. You will need to reuse your originals.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Brake Drum (0:52)
    • Remove the wheel by loosening the lug nuts (replace a lug nut and kick the wheel to break it loose if necessary)
    • Use a hammer and cold chisel on the dust cap. Dent the cap down and out. Turn and repeat until it comes free
    • Remove the 30mm socket using a ratchet and breaker bar
    • Pull the drum free
  2. step : Removing the Brake Shoes (1:43)
    • Using pliers lock on the springs and pull them free
    • Remove the two clips using a flat blade screwdriver
    • Pull the brake shoe free
    • Pull the other brake shoe free twisting until the metal ball comes free from the shoe
    • Remove the springs on the backside of the shoe by pulling the pieces apart
  3. step : Replacing the Brake Shoes (5:25)
    • Push the automatic adjuster on the crossbar removed from old brake into place on the new shoe. With a spring in between the parts
    • Use a wire brush to clean the pads the brake shoes fit onto
    • Make sure the cylinder is not leaking
    • Place grease in the divits on the new brake shoes. Attach the emergency brake cable back to the brake shoe
    • Push the pins (springs) back through into the brake shoes
    • Put the other brake shoe into place and insert the clips and springs
    • Slide cross bar back into place
    • Squeeze the shoes together. To help with inserting the blue springs
    • Center the brake shoes
  4. step : Replacing the Brake Drum and Wheels (10:56)
    • Line up the drum and slide it into place
    • Replace the 30mm nut. Torque it to 170 ft/lbs
    • While torqueing it spin the bearings
    • Replace the dust cap
    • Put the wheel into place and tighten the lug nuts to 100 ft/lbs
    • Pump the brakes until the pedal is firm

Tools needed for replacement:

    General Tools

  • Hammer
  • Chisel
  • Wire Brush
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 30mm Socket
  • 19mm Socket

3.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
0
3
0
0
"Kit"
Do not purchase this kit unless you have a press to install bearings that are not included.
March 8, 2018
Purchased
2 months ago
no pins or bearings
the drums and shoes appeared to be of high quality, but my mechanic would not put them on without the pins or bearings, so I ended up paying $169 for another set of drums (with pins and bearings)...and because they used the pads from this kit, I couldn't return them. Just disappointing they didn't mention the lack of pins.
July 10, 2017
Purchased
10 months ago
Response from 1A Auto
Please contact us at your earliest convenience to set up a return on the brake drums.
July 11, 2017
Alex PStaff
brake review
I sent an email a couple of weeks ago looking to return these. The drums came in separate boxes and that is what I am looking to return. When the mechanic was replacing the brakes he found I needed drums with studs attached and this didn't come that way. He got new drums but used the shoes from this order, so, I was wondering if the drums could be returned. The shoes work great by the way.
July 24, 2017
Purchased
10 months ago
Response from 1A Auto
Please give us a call at 1-888-844-3393 at your convenience to set up the return.
July 24, 2017
Alex PStaff
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Hi there, I am just wondering if this set comes with bearing as well?
Thanks,Mike
Mike G on Dec 4, 2015
BEST ANSWER: Hello, No bearings are include with these here.

Vehicle Fit

  • 2000-2008 Ford Focus Rear Brake Kit Nakamoto

This part replaces:

  • Nakamoto 80090, S747
Part #: 1ABDS00017



Nakamoto
Brand #: 80090, S747

How-to Video:

(13:42 min)