2000-06 Nissan Sentra Window Regulator - 1AWRG00346

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Regulator Option:   without Motor
  • Operation:   Power

This replacement power window regulator is just what you need to get your vehicle in good shape again!


  • LH (Driver Side) FRONT DOOR
  • Power operation
  • Replaces dealer part number: 80721-4M400, 807214M400
  • Does NOT include the power window motor
  • Direct replacement
  • Built to strict quality control standards

This power window regulator makes a great replacement and has good cost savings over a dealer unit.

Please Note:

This window regulator is designed to work with factory style motors only.  Due to variations in aftermarket designs, replacement motors may not have the correct gear style.

Please Note:

This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original. It has been subjected to extensive testing and quality control standards. That is why we offer this regulator with our superior warranty!

Rigorously Tested

Build to strict quality standards

Highest Quality Materials

Made from the highest quality materials for extreme durability and premium performance.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (0:49)
    • Pry off the door pull panel by hand
    • Pry off the window switch panel by hand
    • Disconnect the window switch wiring harness
    • Remove the 10mm Phillips head bolts behind the door pull
    • Pry off the clip at the front of the door panel
    • Remove the Phillips screw at the bottom of the door panel
    • Pry the door handle bezel off with a flat blade screwdriver
    • Pull the door panel off by hand
    • Carefully remove the water shield with a putty knife
  2. step : Removing the Window Regulator (3:48)
    • Move the window by hand until you can access the window bolts
    • Remove the 10mm window bolts
    • Lift the window by hand
    • Turn the window and pull it out
    • Disconnect the window motor wiring harness
    • Remove the three 10mm bolts from the window motor
    • Remove the four 10mm bolts from the window regulator rail
    • Pull the window regulator and motor out of the door
  3. step : Disconnecting the Window Motor (6:06)
    • Remove the three screws from the window motor with a Phillips head ratchet bit
    • Remove the motor from the regulator
  4. step : Connecting the New Motor to the Regulator (6:59)
    • Line up the motor with the regulator
    • Start the three screws by hand
    • Use the Phillips head ratchet bit to tighten the three screws
  5. step : Reinstalling the Regulator (7:37)
    • Start the top left regulator rail bolt by hand
    • Slide the regulator and motor into the door
    • Hang the regulator in place by the bolt
    • Hang the motor in place with its two teeth
    • Thread all the 10mm bolts by hand
    • Tighten all the bolts with the 10mm socket
    • Connect the window motor wiring harness
    • Slide your window into the door, starting with the front corner
    • Push the window on to its track
    • Insert the bolts that connect the window to the regulator
    • Connect the window switch wiring harness
    • Test that the window works
    • Disconnect the window switch wiring harness
  6. step : Reinstalling the Door Panel (10:06)
    • Carefully put the water shield back on
    • Thread the window switch wiring harness through its cavity
    • Put the door panel on
    • Push the door panel clips in
    • Insert the 10mm Phillips bolts behind the door pull
    • Insert the plastic clip at the front of the door panel
    • Insert the Phillips head screw at the bottom of the door panel
    • Push on the door handle bezel by hand
    • Connect the power window switch wiring harness
    • Push the power window switch into the door starting at the front
    • Push the door pull panel into place

Tools needed for replacement:

    General Tools

  • Putty Knife

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • 3/8 Inch Drive Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Wrenches - Metric

  • 10mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2000-2006Nissan Sentra Nissan Sentra Front Power Window Regulator without Motor Driver Side
Part #: 1AWRG00346

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(12:58 min)